[. . . ] Please refer to the relevant laws in your country.
G
No part of this publication may be reproduced, stored or transmitted in any form without prior permission from SHARP Electronics (Europe) GmbH.
® and PlusCode ® are registered trademarks of Gemstar Development
G
Corporation.
G
system is manufactured under license from Gemstar Development Corporation.
SAFETY WARNINGS Observe all warnings for your safety and to ensure trouble free use of your VCR.
INFORMATION Additional information complements instructions.
(i)
VCR REMOTE CONTROL
14. TIMER ON/OFF 5. AUDIO OUT
(This button has no function with these models. )
OPERATE INPUT SELECT TIMER ON/OFF MENU AUDIO OUT
CH
VOL +
15. PLUSCODE
PLUSCODE
CLEAR
MODE OSD
1 4 7
AM/PM
2 5 8 0
3
DISPLAY
6 9
INPUT SELECT
CHANNEL
/
8. RECORD
(The STOP button is also used to switch on the VCR. )
REC PAUSE/STILL
STOP
11. STOP
28. [. . . ] If your VCR has long play facility and you wish
to change the RECORDING SPEED, use / ]to highlight SP. Press [ / ] the [ to select standard play (SP) or long play (LP) as required.
1/2 DA T E 21 / 06 --/---/---/-TAPE
8. If you wish to enter further VIDEOPLUS+ recordings repeat this procedure.
P R S T AR T S T OP 02 12 : 00 13 : 00 --:--:---:--:---:--:--
SP ----
SET
S P E E D :S P / L P : SE L ECT : CHANGE : ENT ER ME NU : E X I T
9. When you have completed entering timer
settings, press MENU to remove the menu from the TV screen.
P L U S COD E
ONC E
.
DA I L Y
10. Ensure that the tape on which you wish to
record is inserted into the VCR, then press TIMER ON/OFF once to place the VCR in TIMER STANDBY mode. will be shown on the display.
WE E K L Y
NOTES:
· You may also access the VIDEOPLUS+ menu by the following procedure:
i. · · · If flashes a video tape has not been inserted into the VCR.
If the video tape is ejected when the VCR tries to record the record protection tab has been removed. If there are further recordings to be made, the VCR will return to TIMER STANDBY.
If problems persist contact the SHARP Helpline on tel: 0990-274277
14
BASIC OPERATION
HOW TO SET A DELAYED RECORDING
You can make a maximum of eight delayed recordings up to a year in advance. To change to12-hour clock operation refer to MANUALLY SETTING THE CLOCK section of this manual. 12-hour clock am/pm can be selected using the AM/PM button on the remote control.
Before you start!
· · If appears on the VCR display, press TIMER ON/OFF to remove the symbol. Check that the VCR clock is displaying the correct time.
SETTING A RECORDING
For example: Recording a programme on channel 3 from 21:05 to 22:30 on July 9th. Press [
/ ] to highlight the setting to be changed and correct it by using the [ / or the NUMBER BUTTONS.
]
4. When all corrections are complete press SET to
confirm, then press MENU to exit.
CANCELLING A RECORDING 1. To cancel a delayed recording, press
[ / ] to highlight the recording to be cancelled, then press CLEAR.
1/2 DA T E P R S T AR T S T OP 2 1 / 0 6 0 2 1 2 : 0 0 1 3 : 0 0 SP --/-- --:--:-- ---/-- --:--:-- ---/-- --:--:-- --
3. Press MENU to exit.
NOTE:
· If there are some programmes to be recorded, do not forget to press TIMER ON/OFF button to return the VCR to TIMER STANDBY mode. If problems persist contact the SHARP Helpline on tel: 0990-274277
17
ADVANCED OPERATION
PLAYBACK OF A VIDEO TAPE
CHECKING THE AMOUNT OF TAPE REMAINING
When you load a video tape into the VCR it can calculate approximately the amount of video tape remaining in hours and minutes. This is useful in determining whether or not there is sufficient tape left to make a recording. When a video tape is playing, the amount of tape remaining is calculated for you automatically. Press DISPLAY on the remote control as many times as necessary until "R" appears on
the VCR display. The tape remaining will be shown on the VCR display in hours and minutes. By pressing the TAPE SPEED button on the remote control the remaining time will change between long play and standard play. For example, in standard play 1 hour 23 minutes is left on the tape:
Pr
in long play 2 hour 46 minutes is left on the tape:
Pr
NOTES:
· · If tape remaining function is interrupted, the remaining time will not be displayed. [. . . ] (hereafter called Sharp) guarantee to provide for the repair, or at its option the replacement, of this product subject to the conditions listed below:
1. This guarantee shall only apply to faults which are due to inferior workmanship or
materials. It does not cover faults or damage by accident, misuse, fair wear and tear, neglect, tampering with the product, or repair other than by a Service Facility appointed by SHARP.
2. As this product is intended for private domestic use only, the guarantee will not apply if
the product is used in the course of a business, trade or profession.
3. [. . . ]