[. . . ] d-Copia 600 d-Copia 800
Operation Guide
PUBLICATION ISSUED BY: Olivetti S. p. A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www. olivetti. com Copyright © 2006, Olivetti All rights reserved
The mark affixed to the product certifies that the product satisfies the basic quality requirements.
The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice.
ENERGY STAR is a U. S. registered mark.
The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment.
Your attention is drawn to the following actions which could compromise the conformity attested to above, as well as the characteristics of the product: · incorrect electrical power supply; · incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the User's Manual supplied with the product; · replacement of original components or accessories with others of a type not approved by the manufacturer, or performed by unauthorised personnel.
All rights reserved. No part of this material may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or by any information storage and retrieval system, without permission in writing from the Publisher.
Take Advantage of Advanced Functions
For information on basic copying, refer to Chapter 3 of the Operation Guide. [. . . ] Failure to do so may cause the originals to jam. )
· · ·
How to Load Originals
Follow these steps to load originals in the document processor. IMPORTANT: Before loading originals, be sure there are no originals left on the original eject table. Originals left on the original eject table may cause the new originals to jam.
2-16
Preparing to Copy 1
Adjust the original width guides to fit the originals.
2
Place the originals. Put the side to be copied (or the first side of two-sided originals) face-up. Slide the leading edge into the document processor as far as it will go.
IMPORTANT: Confirm that the original width guides exactly fits the originals. Pull out the ejection guide for originals of 8 1/2 × 14" (B4) or 11 × 17" (A3).
Ensure that loaded originals do not exceed the level indicated. Exceeding the maximum level may cause the originals to jam.
2-17
Preparing to Copy
Loading Originals on the Platen
To copy books, magazines, or other originals that cannot be loaded in the document processor, open the document processor and place the original directly on the platen. Adjust how the document processor opens by using the document processor angle adjustment lever. Move the lever left to open the document processor 60° and move it right to open the document processor 30°. IMPORTANT: Before opening the document processor, be sure that there are no originals left on the original table or on the original eject table. Originals left on the original table or on the original eject table may fall off the copier when the document processor is opened. Do not move the document processor angle adjustment lever when the document processor is open. Close the document processor before using the lever.
1
Open the document processor.
2
Place the original. Put the copying side facedown and align it flush against the original size indicator plates with the back left corner as the reference point.
Inch models
2-18
Preparing to Copy
Metric models
3
Close the document processor. For originals over 4 cm thick, leave the document processor open during copying. IMPORTANT: Do not push the document processor forcefully when you close it. Shadows may be copied around the edges and in the middle of open-faced originals such as books.
Caution
Do not leave the document processor open as there is a danger of personal injury.
2-19
Preparing to Copy
Selecting the Language
Select the language displayed on the touch panel. Languages Inch models Metric models English, French (Francais), Spanish (Español) and Japanese ( ) English, German (Deutsch), French (Français), Spanish (Español) and Italian (Italiano)
1
Press the System Menu/Counter key.
2
Press [Language].
System Menu / Counter
System Menu Copy Default Language MP tray Setting Machine Default Document Management Register Orig. Size Job Accounting BOX Management Print Report
3
Press the key for the desired language. The touch panel language will change accordingly.
Language
English
Francais
Españ ol
System Menu
2-20
3
Basic Operation
This chapter explains the following operations. · · · · · · · · · · · Basic Copying Procedures. . . 3-2 Selecting Image Quality. . . 3-4 Adjusting Exposure. . . 3-5 Reducing/Enlarging. . . 3-6 Duplex Mode. . . 3-11 Split Mode. . . 3-14 Sort Mode. . . 3-16 Interrupt Mode. . . 3-17 Job Reservation. . . 3-18 Low-Power Mode. . . 3-19 Sleep Mode. . . 3-20
Refer to the Advanced Operation Guide for additional functions.
3-1
Basic Operation
Basic Copying Procedures
Follow the steps as below for basic copying.
1
Open the main power switch cover and move the main power switch to on (| position). After the copier has warmed up, the Start indicator will turn green.
2
Place the originals in the document processor or on the platen. [. . . ] If the paper tears, remove every loose scraps from the copier inside.
12
Push A6 and close the cover A5 securely.
13
Open the cover A7 and remove the jammed paper. If the paper tears, remove every loose scraps from the copier inside.
14 15
Close the cover A7. If the paper tears, remove every loose scraps from the copier inside.
16
Close the cover A8.
6-20
Troubleshooting 17 18
Restore the paper conveyor to its original position and push it back in securely. Return the lever A2 to its original position.
19
Close the front cover.
Duplex Unit
Follow the steps as below to clear paper jams in the duplex unit.
Paper misfeed.
1. Pull out Duplex Unit B1
1
Open the front cover.
2
Pull the lever B1 and pull out the duplex unit.
3
Remove any paper from above the duplex unit. [. . . ]