[. . . ] World-Class Auto Security TM intelliguard 800-IQ Owner's Manual All IntelliGuard-IQ Series systems are covered by one or more of the following Clifford Electronics patents: 4, 158, 874; 4, 233, 642; 4, 327, 444; 4, 383, 242; 4, 430, 685; 4, 845, 464; 4, 887, 064; 4, 890, 108; 4, 922, 224; 4, 997, 053; 5, 081, 667; 5, 146, 215; 5, 157, 375 and other patents Table of Contents Standard Features of the IntelliGuard 8OO-IQ . 14 Remote controlled valet mode entry and exit Keyless entry in valet mode . 17 Smart prior intrusion attempt alert How to interpret the LED status indicator . 21 EXAMPLE 2: Turn off siren sound numbers 4 and 6, then turn on QuietChirps . [. . . ] From the Table of user-selectable features on pages 23 and 24, you would note that the "set a new secret valet code" feature is in column 4, row 6. Enter program mode by turning on the ignition, entering your current valet code, then pressing the PlainView switch to its momentary side for 3 seconds until you hear a chirp. Select column 4 by moving the switch between latched and center 4 times, i. e. : latched, center, latched, center, latched, center, latched, center. After a brief pause, you will hear 4 chirps to confirm that you have selected feature column 4. Select row 6 by pressing and releasing the momentary side of the switch 6 times. To help you count, you will hear a chirp each time you press the momentary side. To enter 31 as your new code, you would press the switch in this manner: momentary, momentary, momentary, latched (you'll hear 3 chirps to confirm the first digit), momentary, latched (1 chirp to confirm the second digit), center. Wait 3 seconds until you hear 2 chirps, indicating the new code has been accepted. Turn off the ignition to exit program mode (you'll hear a 3-chirp confirmation). VERY IMPORTANT: You must immediately test your new secret valet code: Turn on the ignition, enter your new code, then flip the switch to its latched position. If it does not, the new code you programmed and the one you just entered do not match. In such a case, the system will revert to the previous code. Remote controlled valet mode entry and exit You can even enable or exit valet mode with your remote control simply by transmitting channel 9 (LevelShift twice, then button 1). In addition to the above indications, two parking light flashes will confirm that you have remotely enabled valet mode, while a single flash confirms exiting of valet mode. Keyless entry in valet mode Even if valet mode is enabled, you can still remotely control the convenience features. For instance, simply press button 1 (channel 1) as if you were disarming and the doors will unlock (indicated by one parking light flash) and the interior lights will turn on. You can also use the other channels to activate options such as a remote trunk release or remote engine starting. 14 Remote controlled sensor adjustments Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors. You can adjust sensitivity electronically without tools and without even knowing where the sensor is mounted!If the setting(s) of the Proximity Sensor are either too sensitive or not sensitive enough, you may individually test and adjust the settings of each zone. Disarm the system with the remote control, open the driver's window, then select the sensor zone you wish to adjust: a. Ideally, it should chirp when you lean over the driver's seat, but remain silent when you lean toward the window. Ideally, it should only chirp when you are moving within one foot of the vehicle. If you are not satisfied with the detection level and wish to increase sensitivity, press button 2 on your remote control. [. . . ] If you wait more than 10 seconds, the system automatically jumps back to the "Feature Select" position. This is the "stand-by" position: ready for entry of a new programming selection. If no action is taken for the next 60 seconds, the system automatically exits program mode, perfect if you program while driving or if you forget to turn off the ignition. Adding new remote controls For other drivers in your family, or if you wish to control IntelliGuard IQ systems on your other cars with the same remote control, you can buy additional remote controls from any Clifford Dealer (or call our Customer Service Department at 800-824-3208) and program them into the system yourself. Each IntelliGuard 800-IQ will respond to as many as four 12-channel remote controls. [. . . ]