[. . . ] From the Main Menu, navigate to the Diagnostics Menu and select the Display Configuration button. The amount of flash memory residing in the user interface is shown.
Remote Verification
A PC running SIMPLTM Windows® or VisionToolsTM Pro-e and connected to the Crestron control system (with the user interface connected via Cresnet) is required for remote verification. From the Viewport enter Remote | Remote Console | Connect to open the "Select Network ID" window. Click on the OK button and observe the "TPS>" prompt in the Viewport. [. . . ] Re-install the eight base cover screws to finger-tight then, using a Philips screwdriver, tighten an additional 1/8-turn. If the optional external power pack is utilized, connect the plug of the power pack to the touchpanel rear port labeled 24VDC 2A.
Lectern Model Installation Procedure
CAUTION: The memory module and the TPS lectern-model user interface contain ESD sensitive devices. Perform the following procedure while wearing a grounding strap that is properly grounded or on a grounded workstation to avoid damaging the module and/or the user interface. NOTE: The diagrams in this procedure show a TPS-6000L touchpanel but the steps for all other lectern-model TPS user interfaces are identical. This procedure pertains to an interface that is NOT installed into a wall or lectern. If already installed, refer to the latest revision of the user interface Operations & Installation Guide or, if applicable, the back box Installation Guide. Disconnect power and perform the installation procedure in reverse to remove the user interface. The latest version of the Operations & Installation Guide can be obtained from the Downloads page (MANUAL Library) of Crestron's website (www. crestron. com). New users are required to register in order to obtain access to the FTP site. To prevent scratching of the screen (TPS-TPI excluded), place the touchpanel facedown onto a padded surface.
Installation Guide - DOC. 5927
Flash Memory for TPS User Interfaces: TPS-MEM16MB & TPS-MEM32MB · 7
Flash Memory
Crestron TPS-MEM16MB & TPS-MEM32MB
2.
Refer to the diagram below. Using a #1 Phillips screwdriver, loosen and remove the 10 screws that secure the touchpanel rear cover.
Remove Touchpanel Rear Cover Screws
CAUTION: The connectors of any optional card that is already installed may have to be aligned slightly to allow the rear cover to be removed. Align the connectors carefully to prevent damage to the card, cover, or touchpanel.
8 · Flash Memory for TPS User Interfaces: TPS-MEM16MB & TPS-MEM32MB
Installation Guide - DOC. 5927
Crestron TPS-MEM16MB & TPS-MEM32MB
Flash Memory
3.
As shown below, remove the touchpanel rear cover by sliding it towards the bottom of the touchpanel.
Remove Touchpanel Rear Cover
4.
To obtain unobstructed access to the memory socket, remove the PCB blank plate or previously installed TPS-VIDL expansion card. If the PCB blank plate is observed, refer to the diagram on the next page. Using a #1 Phillips screwdriver, loosen and remove the two screws that secure the PCB blank plate and remove the plate.
Installation Guide - DOC. 5927
Flash Memory for TPS User Interfaces: TPS-MEM16MB & TPS-MEM32MB · 9
Flash Memory
Crestron TPS-MEM16MB & TPS-MEM32MB
Remove PCB Blank Plate
4b. If the TPS-VIDL expansion card is observed, refer to the diagram below. Completely loosen the knurled mounting screws and carefully remove the TPS-VIDL from the touchpanel motherboard connector without bending any of the pins on the touchpanel interface connector. TPS-VIDL Removal
10 · Flash Memory for TPS User Interfaces: TPS-MEM16MB & TPS-MEM32MB
Installation Guide - DOC. 5927
Crestron TPS-MEM16MB & TPS-MEM32MB 5.
SIDE CLIP (ONE AT EACH END)
Flash Memory
As shown below, locate the memory socket.
Memory Socket Location
CRESTRON ELECTRONICS INC. ROCKLEIGH, NJ 07647 USA
LOCATION OF MEMORY SOCKET WITH MEMORY MODULE
S R+ RL+ LS
NET 24 Y Z G RS-232 AUDIO INPUT MIC OUT
NOTE POLARITY OF MEMORY MODULE (NOTCH IN CORNER OF BOARD)
6.
Press the two metallic side clips of the socket securing the original module in opposing directions and notice that the module lifts up slightly. [. . . ] Furthermore, this warranty does not cover any product that has had the serial number altered, defaced, or removed. This warranty shall be the sole and exclusive remedy to the purchaser. In no event shall CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages inclusive) arising from the sale or use of this equipment. CRESTRON makes no other warranties nor authorizes any other party to offer any warranty, expressed or implied, including warranties of merchantability for this product. [. . . ]