[. . . ] * TV and Radio gain controls to match the system to your devices for optimum performance. * Sleep mode (ultra-low current draw mode) after 2 minutes with no signal detected. This allows for easy adjustment, yet controls cannot be accidentally adjusted while being handled during installation. [. . . ] SRS1000 Amplifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc
ATE R
Min Ma x Min Ma x Min Ma x
TV Ga in 3D -F
iel
Vo y
Ra dio Ga in
d TV Ra dio
100 3-B Hz AN
Min Ma x Min Ma x Min Ma x
age
r
D
EQ
1kH
2. Wire Harness - 8 pin - Radio High Level
(Speaker Input ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc
R
THEATER SOUND
SRS1000
4. Owner's manual. . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc
----- 1 -----
TH E
UA
z
LIZ ER
10k Hz
SRS1000 Theater Sound Owner's Manual
Owner's Manual
SOU
ND
SR
S1
00
0
SRS1000 Theater Sound Owner's Manual
Front/Rear Panel Description (1)
Front panel view
Radio Gain TV Gain 3D-Field
3-BAND EQUALIZER
TV
Radio
100Hz
1kHz
10kHz
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Front panel description: 1. 100 Hz Band Adjustment---Adjust low frequency response (Bass) of the amplifier when in TV mode . This control has no effect on radio mode. 1 kHz Band Adjustment---Adjust middle frequency response (Midrange) of the amplifier when in TV mode . This control has no effect on radio mode. 10 kHz Band Adjustment---Adjust high frequency response (Treble) of the amplifier when in TV mode . This control has no effect on radio mode.
----- 2 -----
SRS1000 Theater Sound Owner's Manual
Front/Rear Panel Description (2)
Rear panel view
RR LR RF LF
+ _
Hi Level In
TV In Hi Level
Line In TV Radio
SW1 RR RF Trigger SW2 LR LF DC
+ _
R Speaker Out
Made in China
L
R
L
is a trademark of SRS Labs, Inc.
Rear panel description: 1. Using the included 8 pin wire harness, connect the speaker output of the radio to SRS1000. TV In, High Level -- This input is to be used only with monaural TV's (non-stereo) that do not have variable, stereo, line level out put. Do not connect any cable to the TV In , Hi Level Jack if this input is used . 4. Line in , Radio--Connect to variable line output from radio (if available). Do not connect the 8 pin harness to the SRS1000 if this input is used. Use included 16 pin wire harness to apply power, TV mode trigger, and all speaker outputs though this connection. Refer to page 4 for details.
----- 3 -----
SRS1000 Theater Sound Owner's Manual
System Connections (2)
Note: Be sure that left & right speaker channels are connected properly from TV, Radio, and to speakers. Care should be taken to ensure proper polarity (+ to + and - to -).
Car Radio/Tape
Note: Connect Low Level input or High Level input for each device (Radio/TV), not both. [. . . ] 6) Adjust TV volume to approximately 1/4 volume , and adjust TV gain control on SRS1000 until suitable level is obtained.
----- 5 -----
SRS1000 Theater Sound Owner's Manual
7) Adjust EQ until desired sound quality is reached. This is done by turning each of the 3 knobs under "3 Band Equalizer" on the front panel. This control is to compensate for the acoustic properties of small and large vehicles, which are very different. [. . . ]