[. . . ] 15 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Application QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Advanced QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] At this point the local adapter is now assigned as the master adapter in your network. Press and hold the button To proceed securing the remote adapters follow the 3-step process below Local Adapter Local Adapter D-Link DHP-302 User Manual 8 Section 2 - Installation 1. Local adapter Begin by pressing the push button until its AP LED starts to flash. During this flashing phase the adapter is actively waiting for other adapters to sync Press and hold the button Local Adapter 2. Remote (additional) adapters Push the button on the remote adapter until the AP LED begins flashing. (It is important to ensure the local adapter AP LED is still in the flashing state while you do this). Press and hold the button Remote Adapter D-Link DHP-302 User Manual 9 Section 2 - Installation 3. Synchronization complete After a few seconds, successful synchronization should occur. This is visible when the remote adapter's AP LED switches off indicating that it is securely configured. The local adapter AP LED however, will continue to remain solidly lit and the throughput LED should turn Green. Remote Adapter Local Adapter Note: When adding more adapters, repeat steps 1 to 3. At the end of this process, only the local adapter should have the AP LED lit. Also, the adapters will keep their security settings even after the power is removed from the units. To reset / switch-off any adapter security back to default: Depress and hold (up to 15 seconds) the push button until the AP LED turns off. This will reset the unit back to the factory default settings D-Link DHP-302 User Manual 10 Section 2 - Installation Using the Setup Wizard Follow the simple steps below to run the Setup Wizard to guide you quickly through the installation process. If the CD Autorun function does not automatically start on your computer, click Start > Run. In the Run command box type "D:\DHP302. exe", where D: represents the drive letter of your CD-ROM. Click on Install Utility The InstallShield Wizard will begin the DHP-302 software installation. Click Next D-Link DHP-302 User Manual 11 Section 2 - Installation Click Next Click Finish D-Link DHP-302 User Manual 12 Section 3 - Configuration Configuration After you have completed the D-Link Powerline Utility installation wizard, double-click the D-Link Powerline HD Utility icon on your desktop to start the configuration of the DHP-302. Double-click the D-Link Powerline HD Utility icon The utility provides you with the option of setting your own unique Network ID and the ability to prioritize traffic passing through the network. The color of text on the Device Name, Network ID, MAC, and Location columns represent the status of powerline network. · Green text - Powerline network is encrypted with a non-default Network ID. · Red text - Powerline network is encrypted with the default Network ID. · Grey text - Powerline network is not connected due to a different Network ID. D-Link DHP-302 User Manual 13 Section 3 - Configuration Red text on the Device Name, Network ID, MAC & Location columns mean that the powerline network is encrypted with the default Network ID (D-Link). [. . . ] Multimedia applications use UDP (User Datagram Protocol) for data transfer, while database applications use TCP (Transmission Control Protocol) for data transfer. Application QoS: Select an application from the drop-down menu of predefined QoS rules to apply QoS automatically. Click the Save Settings button to apply your settings. D-Link DHP-302 User Manual 18 Section 3 - Configuration Advanced QoS Rule: Select the traffic type (UDP or TCP) to have priority. Note: Rule 1 has priority over Rule 2 D-Link DHP-302 User Manual 19 Section 3 - Configuration System With the power saving mode enabled and the ethernet link activity being down for 15 minutes, the DHP-302 will automatically go into stand-by mode. [. . . ]