[. . . ] ?
Insert coin(s) and press Hunter 1 or Hunter 2 button to start game. Use Sammy 27" Shotgun to (Pump the Shotgun before you shoot the screen each time. ) Select one of 6 states. Colorado, Idaho or Maine for Bear and 3 states Montana, Utah or Alaska for Moose. Bolt-Action Rifle (Ammo x 4), Compound Bow (Ammo x 8) Revolver with scope (Ammo x 6), Muzzleloader (Ammo x 1)
?
?
12 areas per state with one bonus stage after the 6th area. [. . . ] *WARNING* Be absolutely sure that the connector for the hand gun matches exactly the pin position for CN5 (1P Gun) and CN7 (2P Gun) as shown on page 4. Connect 1P Gun connector to CN5, 2P Gun connector to CN7 and turn on Dip switch 2, #8. See page 5 for Dip switch table.
11
· INSTRUCTION DECAL SHEET Put "PUMP BEFORE SHOOTING" Decal Sheet on the front glass of the monitor.
MONITOR
PUMP BEFORE SHOOTING DECAL
AAMA STICKER
· AAMA "ANIMATED VIOLENCE MILD" STICKER Place AAMA sticker on the upper left hand side corner of the marquee.
ANIMATE VIOLENCE MILD
Remove old P. Connect the HARNESSES
· JAMMA HARNESS Connect the JAMMA Harness to the edge connector on the TROPHY HUNTING Main P. C. BOARD. · GUN HARNESS Connect the Gun Harness to the Gun Connectors located on the Main P. C. Board components side, at CN5 & 6 and CN7 & 8 connectors on the P. C. Connect Gun Connector to CN5 & 6 and CN7 & 8, correctly, as shown below.
10 pin connector from GUN Assy (1P)
10 pin connector from GUN Assy (2P)
CN 5
10
1 CN 6
CN 7
10
1 CN 8
Connectors on the Main PCB
Connectors on the Main PCB
12
10. TEST MODE
Entering the TEST MODE
If you need to check the condition of the game circuitry and controls, you can use the TEST MENU. The game will go into TEST MODE (diagnostics) and the screen appears as follows:
Select TEST
Use this screen to choose which of the 7 screens you want to see. To check the functioning of each switch, activate it and watch the corresponding OFF letters change to ON. If the ON and OFF letters do not appear correctly, check the Harness connections and Switches. * Press START button and Gun trigger simultaneously to exit.
I/O TEST
COIN A COIN B SERVICE TEST 1P GUN START PUMP TRIGGER : : : : OFF OFF OFF OFF 2P GUN START PUMP TRIGGER
: OFF : OFF : OFF
: OFF : OFF : OFF
PRESS START & GUN TRIGGER TO EXIT
5. * Press START button and Gun trigger simultaneously to exit.
SOUND TEST
SOUND CODE 000 BLAK_SHOT
PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO PLAY
PRESS START & GUN TRIGGER TO EXIT
6. MEMORY TEST
Use this screen to check RAM and ROM on the Main P. C. B. If you get the word ERROR, check the mounting of RAMs or ROMs on the Main P. C. B. and if ERROR reappears, it needs to be replaced.
MEMORY TEST
WORK RAM : OK BACKUP RAM : OK ROM (U06) ROM (U07) : OK : OK
* This mode will automatically exit after testing is finished.
14
7. OPTIONAL SETTING
HIGH SCORE CLEAR
If you desire to clear HIGH SCORE data, do the following. Select YES by pressing START BUTTON and pressing GUN TRIGGER to clear HIGH SCORE data. The screen will return to previous screen automatically after clearing HIGH SCORE data.
OPTIONAL SETTING
1. RETURN TO TEST MENU PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO SELECT
HIGH SCORE CLEAR
ARE YOU SURE YOU WANT TO CLEAR HIGH SCORE?YES g NO PRESS ST ART BUTTON TO CHOOSE PRESS GUN TRIGGER TO SELECT
NOTE: Do not proceed if Gun test is accurate.
GUN DATA DEFAULT
If you have problem with Gun sighting , you may have to clear the Gun data. After clearing Gun data, the game will be reset to factory default setting. [. . . ] This limited warranty is invalid for any product that upon examination, is deemed to have been subject to misuse, improper repair or installation, neglect or violation of specification or other instructions published by Sammy USA Corporation. There are no additional warranties which extend beyond those limited warranties described above. The limited warranties described above shall be in lieu of any other warranty, express or implied, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.
Return Merchandise Authorization
1. Contact your authorized Sammy USA distributor to receive a Return Merchandise Authorization for return. [. . . ]