[. . . ] Commands are transmitted by radio (frequency 433. 42 MHz). With an INIS RT, the functioning of the EOLIS receiver RTS is a trip switch type : v, stop, w, stop, . . . 1 Installation: 2 LED Programming button LMN N L SC Ref. 5003510 Characteristics: t Mains supply : 220-240 V~ 50/60 Hz t Protection index: IP 44 t Operating temperature: -20°C to +50°C t Class II product once installed t Normally polluted environment Hereby, SOMFY, declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity is available at the web address www. somfy. com Heading CE Built-in manual security control Before connecting the unit, you must read the instructions carefully. A Mounting of the EOLIS receiver RTS 2 : Recommendations : 150 mm 150 mm 40 mm t Install the EOLIS receiver RTS with the cables entry pointing downwards to avoid water infiltration. [. . . ] t minimum distance between two receivers : 20 cm. ® B Cabling of the EOLIS receiver RTS 2 : The EOLIS receiver RTS is compatible with all standard SOMFY motors. Respect the electrical standards in force as well as the following points: - disconnect the mains before carrying out any work. - be careful to avoid static electricity which could damage some electronic components. - use flexible cables - ensure that no longitudinal forces act on the cable carriers after installation - do not forget to connect the earth wires. Cabling of the EOLIS sensor EOLIS sensor Eolis receiver RTS Eolis sensor SC LMN N L SC Mains RTS control or INIS RT OR L = Main phase LT motor common N L Earth Neutral Phase N = Main neutral N = Motor neutral L = Motor up M = Motor down = WIND input SUPPLY 230V - 50 Hz SC = COMMON input WARNING : if the awning moves DOWN when pressing the UP button of the RTS control, invert the brown and black motor wires. Cabling / fixing of the EOLIS sensor 1. Put and screw the front box. C Wind function : The wind threshold can be adjusted by the potentiometer to accommodate wind speeds between 10 to 50 Km/h. To record these positions, the EOLIS receiver RTS has to record the time for the awning to go from its top to the IP and also the time from its bottom one to the IP. RECORD THE INTERMEDIATE POSITION FROM THE TOP OF THE AWNING STOP Push simultaneoustly on the DOWN and IP button of the RTS control until the awning begins to move (about three seconds). Stop the awning at the intermediate position you wish with the RTS control (if necessary, adjust this position with v and w push buttons). IP 1 2s Push the IP button of the RTS control during two seconds. µ The EOLIS receiver RTS has memorized the 1st intermediate Non-binding document. Products and references in this document are subject to change without prior notice. © SOMFY 12/99 Set the awning at its UP limit with the RTS control. position. RECORD THE INTERMEDIATE POSITION FROM THE BOTTOM OF THE AWNING STOP Set the awning at its DOWN limit with the RTS control. Push simultaneoustly on the UP and IP button of the RTS control until the awning begins to move (about three seconds). Stop the awning at the intermediate position you wish with the RTS control (if necessary, adjust this position with v and w push buttons). IP 2 2s Push the IP button of the RTS control during two seconds. µ The EOLIS receiver RTS has memorized the 2nd intermediate position. REACH THE INTERMEDIATE POSITIONS DELETE AN INTERMEDIATE POSITION To delete an intermediate position, press briefly the IP button of the RTS control to reach the intermediate position you wish to delete, then press continuoustly the IP button of the control until the led stops blinking (approx. [. . . ] 8 sec. ). µ The concerned IP is deleted. IP1 or To reach one of the intermediate positions, set the awning is at its UP (for IP1) or DOWN (for IP2) limit, then press briefly the IP button of the RTS control. µ The awning will move and stop at the dedicated intermediate position. IP2 Diagnosis The LED on the RTS control does not light. The led of the RTS control lights, but the motor does not operate. Check the battery of the RTS control. [. . . ]