[. . . ] CONNECTING BLUETOOTH ENABLED MOBILE PHONES, GPS OR MP3 (A2DP) DEVICES . THE SOUND OF MUSIC: Built-In FM Radio and external MP3 Player (cable option) . 11 7. 2 CABLE CONNECTING YOUR MP3 PLAYER OR OTHER EXTERNAL AUDIO SOURCES . Our manuals are updated periodically in order to include the very latest features as well the new options and functions of your new scala rider G4 PowerSet headsets. [. . . ] USING THE INTERCOM 9. 1 INTRODUCTION The scala rider PowerSet provides you with an impressive Bike-toBike Intercom range by simply flipping up the antenna. The flip-up antenna allows you to maximize the intercom range with other bikers at up to 1 mile / 1. 6 km (subject to terrain). The antenna is also useful when riding in dense urban environments that may affect the transmission quality. You may keep the Flip-up Antenna for extended range flip-up antenna open when not using the intercom, even though there is no particular need to do so. The scala rider G4 PowerSet package contains two factory paired G4 headsets. To set up additional Intercom Bluetooth connections, you must first pair your G4 headset with the other headsets. Once completed, the headsets will remain paired and automatically recognize each other whenever they are within range. HEADSETS TO BE PAIRED Your G4 with a third G4 unit Your G4 with one G4 and one Q2 unit Your G4 with two Q2 units Your G4 with one G4 and one other scala rider model Your G4 with one Q2 and one other scala rider model Your G4 with two other scala rider models Your G4 as part of 4-Way intercom call configuration Channel "A" Button Channel "B" Button GO TO SECTION 9. 10 b 9. 11 c 9. 11 c 9. 11 c 9. 11 c 9. 11 c 9. 10 c The two headsets in your retail box are already factory paired and ready to use. Unless you wish to add additional bikers for a 3-way or 4-way call, you can skip the following explanation and proceed directly to section 9. 4 Read the following if you want to set up 3-way or 4-way calls and/or if you wish to pair your headset(s) with earlier scala rider models: Since the scala rider G4 can be paired with all models among the scala rider family, we recommend that you first pair it according to your preferred configuration and then change or modify as often as you wish later as the need arises. For example: If you typically use the intercom to communicate with two friends who both use G4 units, then you should pair it as described below in section 9. 10 b. Therefore, please select your initial pairing preference now amongst the following options in the table below and following that, refer to the pairing procedure as described in the respective section of this manual. When done, return to the explanations in section 9. 4 "Initiate Intercom Calls". Select your preferred Pairing Option HEADSETS TO BE PAIRED Your G4 with another G4 Your G4 with a Q2 Your G4 with one earlier scala rider model 14 scala rider® G4TM PowerSet GO TO SECTION 9. 10 a 9. 11 a 9. 11 b 9. 4 INITIATE INTERCOM CALLS There are two ways to start an Intercom call with headsets that are paired to your scala rider G4 (make sure you are in Standby mode): VOICE CONNECT: Preferred for relatively brief conversations as it takes the channel into standby mode after 30 seconds of silence Start talking loudly Once you start talking loudly, an Intercom call will be established with both paired headsets, CHANNEL "A" and CHANNEL "B" (if both are available). The Intercom call will stay on until all participants remain silent for 30 seconds (Applicable for 2-way communication). CHANNEL BUTTON CONNECT: Preferred for extended conversations as it leaves the channel open and active Single tap the CHANNEL "A" Button to add or remove the CHANNEL "A" headset from an Intercom call. Single tap the CHANNEL "B" Button to add or remove the CHANNEL "B" headset from an intercom call. NOTE: While the Intercom is on, the Redial and Voice Dial functions will be disabled. 9. 5 RECEIVING INTERCOM CALLS Once another paired headset tries calling you via intercom, the call will begin almost instantly. NOTE: The headsets' priority modes have been set to avoid incoming intercom calls from interrupting mobile phone calls and GPS instructions in progress. In such case the intercom caller will hear a busy signal and you will hear two beeps, indicating that an intercom caller is trying to page you. (see section 4. 3 for details on audio priorities of paired devices). 9. 6 ENABLE/DISABLE VOICE CONNECT FEATURE (VOX) The G4 offers VOX technology for safe and hands-free operation of some key functions. To reject an incoming call, you need only to remain silent for about 15 seconds. While on standby press and hold the Volume Up and Volume Down Buttons simultaneously for three seconds until you hear a beep. The default status is Voice Connect enabled. NOTE: The Enable/Disable Voice Connect feature affects only the Intercom functionality. b. Busy Status (When using a G4 headset) When attempting an Intercom call with a headset that is already on a Phone/GPS/Intercom call, you will hear two beeps indicating the other headset is busy. Automatic Reconnection of the Intercom If your headsets get disconnected because they exceed the intercom range, they will automatically try to reconnect when they are again within range. [. . . ] The Product is manufactured in accordance with Annex II of the above directive. Declaration of Conformity (DOC) The scala rider G4 headset is compliant with and adopts the Bluetooth® Specification 2. 1 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. [. . . ]