[. . . ] 4-077-172-11(1) Color Rear Video Projector Operating Instructions KP-48V85 KP-53V85 KP-61V85 © 2000 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the TV to rain or moisture. CAUTION When using TV games, computers and similar products with your projection TV, or viewing a TV station whose logo always stays on the screen, keep the brightness and contrast functions at low settings. If a fixed (nonmoving) pattern such as a station logo is left on the screen for long periods of time, especially at a high brightness or contrast setting, the image can be permanently imprinted onto the screen. These types of imprints are not covered by your warranty because they are the result of misuse. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR Note on Caption Vision This television receiver provides display of television closed captioning in accordance with §15. 119 of the FCC rules. PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ADRIR NO ABRIR CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note on convergence adjustment Before you use your projection TV, make sure to adjust convergence. [. . . ] Tip z 5 Move the joystick up or down to make Move Select Exit MENU your selection and press to activate it. The previous screen will reappear. You may also move the joystick right to activate your selection. You can also use the MENU, / and buttons inside the front drop-down panel of the projection TV for the menu selection. 33 Adjusting Your SET UP (menus) (continued) Using the Video Menu Video Mode: Vivid Picture Adjustment Trinitone: High Noise Reduction :Off ch Mode Customized picture viewing Move Select Exit MENU For detailed information on using the remote control to modify menu settings, refer to "Learning Menu Selection" on page 33. You can choose one of five different video modes that best suits the program you are watching. You can also perform the "Picture Adjustment" (such as "Brightness, " "Color, " etc. ) for "Movie, " "Personal 1" or "Personal 2" to suit your taste. Standard: Select to display a standard picture for normal viewing environments. Movie: Select to display a finely detailed picture for low light environments. Personal 1, Personal 2: Select to customize the "Picture Adjustment" of the Video menu according to your personal preference. Press PICTURE MODE on the remote control for direct selection of a "Mode" setting. First select "Movie, " "Personal 1" or "Personal 2" from "Mode, " then highlight the desired option using the joystick and press to display the adjusting slider of the selected option. Personal 1 Picture: Adjust slider right (up) to increase picture Picture contrast; left (down) to decrease it. Brightness Color Brightness: Adjust slider right (up) to brighten the Hue Sharpness picture; left (down) to darken it. Color: Adjust slider right (up) to increase color intensity; left (down) to decrease it. Move Select Exit MENU Hue: Adjust slider right (up) to increase the green tones; left (down) to increase the red tones. Sharpness: Adjust slider right (up) to sharpen the picture; left (down) to soften it. ch Picture Adjustment Picture adjustment To select the Video Display menu: / Highlight / Select MENU To restore the factory settings Press RESET on the remote control while the Video menu is selected. To restore each "Mode" to the factory setting, press RESET after selecting the mode to be reset. Trinitone White intensity adjustment High: Select to give the white colors a blueish tint. "Noise Reduction" can be set separately from the "Mode" settings of the Video menu. Noise Reduction Noise reduction 34 Using the Audio Menu Audio Treble Bass Balance MTS/SAP: Stereo On Auto Volume: Effect: Trusurround Speaker: On Audio Out: Variable SAVA SP Control Move Select Exit MENU Treble Sound adjustment Adjust slider right (up) to increase high pitched sounds. When the sound is intermittent due to poor reception conditions, select "Stereo" or "SAP. " Stereo: Select for stereo reception when viewing a program broadcast in stereo. (non-SAP programs will be muted when this feature is selected) Mono: Select for mono reception. (use to reduce noise during stereo broadcasts) MTS/SAP Quick MTS access: Press on the remote control to cycle through the "MTS/SAP" options as follows: Stereo n SAP n Mono. On: Sound output coming from TV speakers have the volume level equalized for all channel audio inputs when broadcasts have different sound transmission levels. Off: Sound output coming from the TV speakers varies according to the received channel. "Effect" can only be set when "Speaker" is set to "On" or "Off. " Trusurround: Produces a virtual surround effect for Dolby-surround encoded programs. Quick Effect access: Press on the remote control to cycle through the "Effect" options as follows: Trusurround n Simulated n Effect Off. } Sliders Bass Sound adjustment ch Balance Sound adjustment MTS/SAP Enjoy stereo, bilingual and mono programs. For detailed information on using the remote control to modify menu settings, refer to "Learning Menu Selection" on page 33. To select the Audio Display menu: / Highlight / Select Auto Volume Adjust the sound level. MENU Effect To restore the factory settings Press RESET on the remote control while the Audio menu is selected. Customizes surround sound effects based on the program's audio type. (continued) 35 Adjusting Your SET UP (menus) (continued) Speaker Custom selection of audio output source On: Select to listen to the sound from the projection TV speakers alone. [. . . ] (see "Cable" on page 39) · Use "Auto Program" to add receivable channels that are not presently in the TV's memory. (see "Auto Program" on page 39) Cannot gain enough volume when · Increase the volume at the cable box. using a cable box Projection TV malfunctions when using the S-Link function CHANNEL INDEX does not display all available channels · Make sure the projection TV's power cord is connected securely to the wall outlet. (see "Using the S-Link Function" on page 20) · Make sure "Cable" is "On" in the Channel Set Up menu. [. . . ]