[. . . ] Philips Professional and Business Solution
22HFL3350D 26HFL3350D 32HFL3350D
EN
SETUP MANUAL
Table of contents
1 1. 1 1. 2 1. 3 2 2. 1 3 4 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 5 6 7 7. 1 72 7. 3 7. 4 7. 5 7. 6 7. 7 7. 8 7. 9 Important 4 Safety . 6 Remote control 8 Get started 9 Position the TV. 11 Remote control overview 13 First time setup 15 Setup BDS mode 16 Access setup menu . 22 8 8. 1 8. 2 9 9. 1 9. 2 9. 3 Clone configuration 23 From Cloning to TV . [. . . ] C WARNING Before you connect the TV to the power outlet, ensure that the power voltage matches the value printed under the cable cover. To easily disconnect the TV from the power outlet, ensure that you have full access to the power cord at all times. When you disconnect the power cord, always pull the plug, never the cable.
44
Connect the mains cord
B WARNING Verify that your mains voltage corresponds with the voltage printed at the back of the TV. To connect the mains cord D Note The location of the mains connector varies according to TV model. Be sure the + and - ends of the batteries line up with the markings inside the case. D Note Remove the batteries if not using the remote control for an extended period of time.
2. Push the CAM in as far as it will go.
46
Prepare TV for digital services
Scrambled digital TV channels can be decoded with a Conditional Access Module, inserted with a smart card (CAM) provided by a digital TV service operator. The CAM may enable several digital services, depending on the operator and services you choose (for example, pay TV). Contact your digital TV service operator for more information about services and terms. 461 Using the Conditional Access Module B WARNING Switch off your TV before inserting a CAM. Following the directions printed on the CAM, gently insert the CAM into the Common Interface slot on the side of the TV.
3. Slide the battery cover off the back of the remote control.
OSD display OSD display Display message Welcome message line 1 Welcome message line 2 Welcome message ti. . . Enable CI slot Enable teletext Enable MHEG
Enable CI slot On Off
4. Press MENU or M to exit.
EN-12
5
Remote control overview
1. Only for models with clock display.
This section provides a detailed overview of remote control features.
1 19 18 17 2 3 4 5 6 7 8 16 9
7. Navigation keys Up Î, Down ï, Left Í and Right Æ keys navigate the menu. Only for models with clock display.
15 14
10
11
13
12
EN-13
EN
18. Teletext appears on the right.
EN-14
6
First time setup
EN EN-15
The first time the TV is switched on, a language selection menu appears.
Please select your language
Press OK or the green colour key on your remote control to continue
Select your language and follow the on-screen instructions to setup the TV. E Tip Youcanskipthefirsttimesetupprocedures by pressing MENU on the TV's control twice.
7
Setup BDS mode
Setup menu BDS mode Local keyboard locked Remote control OSD display Switch on volume 50 Maximum volume 100 Switch on channel Power on BDS mode On Off
The TV is designed to operate as BDS Hotel Mode, which offers the following benefits: · Disable user menu. · Setup Menu via the setup remote control or guest mode remote control. · Disable the VOLUME +/-, PROGRAM +/- and MENU buttons on the TV. D Note For BDS mode settings to take effect, turn the TV set off, then on again. [. . . ] Press ï to select USB break-in.
712 Set auto scart
Set the TV to switch to the source where scart signal is detected. Press ï to select Auto scart.
Setup menu Switch on channel Power on Low power standby Clock Auto scart USB break-in Monitor out Blank current Channel
USB break-in On Off
3. Press ï to select Store - go right and press Æ to save setting.
Setup menu Maximum volume 100 Switch on channel Power on Low power standby Clock Auto scart USB break-in Monitor out
Auto scart AV1 Power ON SCART Off
3. · AV1 Select to switch TV automatically to AV1 when scart cable is connected to the AV1 connector. [. . . ]