[. . . ] Note : It is essential that the CODE CARD be kept in a safe place outside the vehicle. The accompanying sticker should be attached to the inside of the vehicle windshield/ window.
!
If an incorrect code number is entered, the prompt CODE with the four stars is displayed again. After entering incorrect code three times WAIT is displayed and the unit is disabled for approx. Note : The waiting time applies only to ignition and unit switched on. [. . . ] If the selected station has no PTY characteristic (see also page 28) NO PTY appears. In order to activate search, select radio menu mode and then and press multifunction button "PT". Pre-select the desired PTY code using the multifunction button " " or " ". The previous program is selected if no station with the selected PTY code is receivable. The unit switches to station button plane if there is no further actuation within 10 seconds.
FM 1/FM 2 station - retrieve/store
Store: 10 frequencies or programs can be stored on each of wavebands FM 1 and FM 2. Press multifunction button for 2 - 4 seconds in order to store the desired station or program. The frequency is displayed if the station cannot be identified.
12
USEnglisch. bk : RUNDFUNK. fm Seite 13 Freitag, Februar 1, 2002 10:33 AM
Radio Operation
AM station - retrieve/store
Retrieve: Press multifunction button "1 - 0". Search for the desired station and press the multifunction button until the station button number is displayed.
AM / FM autostore
Select desired waveband. Then press multifunction button "AS" repeatedly until AS-SEEK is displayed. The 10 stations with the best reception are stored under the station buttons in order of quality. The radio switches back to the station button plane
Manual tuning
Select radio menu mode and then turn the right rotary control. Protect the CDs against direct sunlight and from heat sources such as heaters, etc. Before playing, clean the CD with a commercially available cleaning cloth, wiping from the center outwards. Solvents such as petrol, thinners and other commercially available cleaners and antistatic sprays must not be used.
Correct
Incorrect
Incorrect
Correct
Operational readiness of CD/MD changer
If a CD/MD changer is connected to the car radio, this is ready for operation as soon as it has been loaded with the filled CD magazine or with MDs. Further operation is performed via the car radio control panel.
19
USEnglisch. bk : CD. fm Seite 20 Freitag, Februar 1, 2002 10:33 AM
CD/MD Changer Operation
CD magazine - load / unload
In order to remove the CD magazine, open the sliding cover on the changer and press the eject button. In order to ensure the fastest possible CD change, the magazine should be fully loaded from compartment 1.
Playing CD/MDs
Press button repeatedly until the CD/MD changer operation is switched on. The last CD/MD which was being played, is played from the position in which it was left before switching off. The desired CD/MD can be selected via the multifunction buttons "1 - 6". Subsequently, the magazine compartment number and the number of the current track for the selected CD/MD are displayed. After playing the last track of a CD/MD, the next CD/MD in the magazine is automatically selected and played.
20
USEnglisch. bk : CD. fm Seite 21 Freitag, Februar 1, 2002 10:33 AM
CD/MD Changer Operation
Track skip - forwards / reverse
Turn right rotary control to right / left. If the track has been playing for longer than 10 seconds when the return function is triggered, a return to the beginning of the track takes place. Through further turning of the right rotary control, several tracks can be skipped over in forward or reverse directions. [. . . ] The setting is stored automatically.
23
USEnglisch. bk : USER. fm Seite 24 Freitag, Februar 1, 2002 10:33 AM
User Menu
User memory
Request user menu, then set USER using the right rotary control. Using the multifunction buttons " " or " " a choice of three different users is available. Both tone settings and the last selected station as the unit was switched off are stored in each user memory.
LED setting
The flashing of the LED (flashes when unit is switched off) can be switched on or off using this function. Pressing the multifunction buttons " " or " " enables a choice between LED ON and LED OFF.
GAL setting
The GAL is a car radio control circuit which automatically adjusts the car radio volume according to vehicle speed. [. . . ]