[. . . ] ISO 9001 CERTIFIED www. liteputer. com. tw DX-404 4 Channel DMX Dimmer Pack USER MANUAL Lite-Puter Enterprise Co. , Ltd. www. liteputer. com. tw sales@liteputer. com. tw DX-404 [EUM-A] Lite-Puter ISO 9001 CERTIFIED www. liteputer. com. tw INDEX Chapter 1. DX-404 INTRODUCTION 1-1 Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 6 1 DX-404 [EUM-A] Lite-Puter ISO 9001 CERTIFIED www. liteputer. com. tw Chapter 1. 1-1 Feature DX-404 Introduction Maximum 5A per channel, total 15A!Warm up setting 0---6% Automatic warm up function, protects loads and extend the life of bulbs. 1-2 Specification Power Output Signal input/ output Signal connector Location Weight Dimension 210 AC 100-120V, AC 200-240V, 45-63Hz, 2 input Maximum 5A per channel, total 15A. DMX512/ 1990 XLR 3Pin, 6P4C, RJ11 telephone jack TRUSS hanging or desktop operation. DMX DIMMER PACK ON FCN DMX CONTROL OFF 1 2 3 4 88 240 2 110 120 DX-404 [EUM-A] Lite-Puter 83 ISO 9001 CERTIFIED www. liteputer. com. tw 1-3 Front Panel, Rear Panel DX-404 4CH. DMX DIMMER PACK ON FCN DMX CONTROL OFF 1 2 3 4 1 2 3 4 5 7 8 6 14 2 13 12 F F F CH-4 CH-3 CH-2 CH-1 11 10 F US US US US 3 1 1 3 2 2 E E E E 9 14 13 12 F F F CH-4 CH-3 CH-2 CH-1 11 10 F US US US US 3 1 1 3 2 E E E E 9 3 DX-404 [EUM-A] Lite-Puter ISO 9001 CERTIFIED www. liteputer. com. tw Front Panel introduction 1. 4 LED display Function key Pad AC power input 15A Rear Panel introduction 10. [. . . ] 3 It is allowed for setting more than 1 piece of DX-404 at the same start address. 2-3 Dimming / Switching Setting STEP-1 pressDMXkey into DMX status STEP-2 press and hold theFCNkey for 3 sec Default settingall channel are dimming mode STEP-3 pressFCNkey to select channel STEP-4 pressorto select dimming mode or switching mode 5 DX-404 [EUM-A] Lite-Puter ISO 9001 CERTIFIED www. liteputer. com. tw (dimming) (Switching) 2-4 warm up setting (0. . . 6%) STEP-1 pressFCNkey STEP-2 pressFCNkey to select the setting channel, EX : select channel 1 STEP-3 press, key to adjust Channel 1 set on 6% for warm up 2-5 Channel output status preview STEP-1 Enter to DMX status and pressDMXkey STEP-2 pressorto preview 2-6 Switching STEP-1 select the channel and press blue key CH-1~CH-4to switching 2-7 DMX status & DMX address a. pressDMXto DMX status b. 10 minutes unused of unit, the DMX will activate to DMX status 6 DX-404 [EUM-A] Lite-Puter [. . . ]