[. . . ] · Process control signal (4 to 20 mA) and commercial CT input (0 to 1 A or 0 to 5 A) supported. · Easy wiring with ferrules 2 × 2. 5 mm2 solid or 2 × 1. 5 mm2 standard ferrules. UL certification pending. Model Number Structure Model Number Legend K8AB-Measuring Current 1: 2 to 20 mA AC/DC, 10 to 100 mA AC/DC, 50 to 500 mA AC/DC 2: 0. 1 to 1 A AC/DC, 0. 5 to 5 A AC/DC, 0. 8 to 8 A AC/DC 3: 10 to 100 A AC, 20 to 200 A AC (See note. ) Note: The K8AB-AS3 is specially designed to be used in combination with the OMRON K8AC-CT200L Current Transformer (CT). [. . . ] Used to set the startup lock time to 0 to 30 s. Function Selection DIP Switch ON DIP Switch Functions Function SW1 Not used. Resetting method Relay drive method OFF ON OFF ON OFF ON SW4 Operating mode OFF ON Not used. Manual reset Automatic reset Normally open (normally OFF) Normally closed (normally ON) Overcurrent monitoring Undercurrent monitoring OFF OFF Default OFF OFF SW1 SW2 SW3 SW4 SW2 DIP Switch SW3 Cat. N142-E1-01 Single-phase Current Relay K8AB-AS 5 Dimensions K8AB-AS 22. 5 100 5 90 5 OMRON CT K8AC-CT200L 9. 3 1. 7 9. 3 1. 7 11 63 54 50 4. 7 Four M4 × 6 screws 20 17 8. 5 13. 5 34. 5 81. 5 33. 5 6 76 Two M5 screw holes or two 5. 5-dia. holes Mounting Hole Dimensions 14. 5 57 86 14. 5 5. 2 30 dia. 10 10 1. 8 4. 1 76 5. 9 20 6 Single-phase Current Relay K8AB-AS Cat. N142-E1-01 Safety Precautions Precautions for Safe Use Make sure to follow the instructions below to ensure safety. · Outdoors, or places subject to direct sunlight or wearing weather. · Places where dust, iron powder, or corrosive gases (in particular, sulfuric or ammonia gas) exist. Make sure to thoroughly understand all instructions in the Instructions Manual before handling this product. Make sure to confirm terminal makings and polarity for correct wiring. Operating ambient temperature and humidity for this product must be within the indicated rating when using this product. 10. To enable an operator to turn off this product easily, install switches or circuit breakers that conform to relevant requirements of IEC60947-1 and IEC60947-3, and label them appropriately. 11. For DC input, use a SELV power-supply capable of overcurrent protection. Specifically, a SELV power-supply has a double or reinforced insulation for input and output, and output voltage of 30 Vr. m. s with 42. 4 V at peak or DC60V maximum. Make sure to use setting values appropriate for the controlled object. Failure to do so can cause unintended operation, and may result in accident or corruption of the product. Only use this product within a board whose structure allows no possibility for fire to escape. About Installation 1. (If you do not secure space for heat dissipation, life cycle of the product will be compromised. ) 3. To avoid electrical shocks, make sure that power is not supplied to the product while wiring. To avoid electrical shocks, make sure that power is not supplied to the product when performing DIP switch settings. Noise Countermeasures 1. [. . . ] Actual performance is subject to the OMRON Warranty and Limitations of Liability. CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with your OMRON representative at any time to confirm actual specifications of purchased product. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0. 03937. [. . . ]