[. . . ] M071-E1-01A
WD30-ME/-SE/-ME01/-SE01
DeviceNet Wireless Units
OPERATION MANUAL
Notice (1) This manual may not be copied, reproduced, or reprinted, in whole or in part, without permission. (2) The specifications listed within this manual may be revised without prior notice. However, if you should find any errors or inconsistencies, please contact the OMRON business office. Be sure to tell us the revision number of the manual in which you found the error.
Copyrights and Trademarks DeviceNet is a registered trademark of the OpenDeviceNet Vendor Association (ODVA). [. . . ] · The purpose of each test is as follows.
Test Installation test
Content/Purpose Adjusts the installation position (confirmation of receiving wave, etc. ) and the setup conditions (selection of available frequencies). Both master and slave stations require the switch Checks the wireless communication status with each slave station in a system in operation. This is a switch operation from the master station.
Test timing At installation At advance on-site test
Confirmation test
At confirmation after installation At maintenance and inspection
Wireless channel monitor Obtains the receiving wave level of the frequency band (all At installation channels) to allow for the selection of the available channels At advance on-site test (frequency band).
72
Installation Test
Section 5-2
5-2
Installation Test
This test is for adjusting the installation position (confirmation of receiving wave, etc. ) and the setup conditions (selection of unused frequencies, selection of transmission output, etc. ) at installation. Both master and slave stations require the switch operation.
5-2-1
Preparation
· The DeviceNet master and DeviceNet slave do not need to be connected for the installation test. · Set the WNODE switch of the wireless master station to "00" and the WNODE switch of a wireless slave station to "01" to "64", avoiding duplication. · Since both the wireless master stations and wireless slave stations require the transmission power supply, connect them to the power supply via the DeviceNet cable prepared for a micro-connector.
5-2-2
Test procedure
Master station
W NODE
901
901
X10
X1
901
SW2 RUN TEST SET
78
W CH
901
X10
X1
SW3
ON 12345678
1. Set the mode select switch of the wireless master station to "TEST", and the WNODE switch to the WNODE number of the wireless slave station to be tested. Set SW3 to "bit 4 = ON".
78
78
78
456
23
23
23
Slave station
W NODE
901
901
78
78
X10
SW2 RUN TEST SET
78
W CH
901
78
X10
SW3
ON 12345678
Master station
MS NS WS
Slave station
MS NS WS
N NODE
901 901
78
23
SW2 RUN TEST SET
N NODE
901 901
78
23
SW2 RUN TEST SET
78
78
X10
X1
SW1
ON 1234
X10
X1
SW1
ON 1234
Master station
MS NS WS
Slave station
MS NS WS
N NODE
901 901
78
23
SW2 RUN TEST SET
N NODE
901 901
78
23
SW2 RUN TEST SET
78
78
X10
X1
X10
X1
SW1
ON 1234
SW1
ON 1234
456
456
456
456
456
456
23
456
23
23
456 456
2. Set the mode select switch of the wireless slave station to "TEST".
X1
901
X1
23
23
3. Turn on the communication power supplies of the wireless master station and all wireless slave stations. The system is in test operation status.
23 23
23
456
23
456
456 456
456 456
4. The LED display shows the receiving wave level "L1 to L9", if the wireless master station and the wireless slave station to be tested have been installed within the distance where both stations can receive the electric wave from each other.
73
Installation Test
Section 5-2
If the WS LED lights green, this means that the wireless communication link has been established. If the electric wave is weak, adjust the position of the wireless slave station so that receiving wave level is stabilized in L5 or higher.
Master station
MS
Slave station
WS MS NS WS
NS
The LED display shows the receiving wave level "L0" if the devices have been installed
N NODE
901 901
78
23
SW2 RUN TEST SET
N NODE
901 901
78
23
SW2 RUN TEST SET
78
78
outside the distance where they cannot receive the electric wave from each other. Set the WNODE switch of the wireless master station to the WNODE number ("00" for this example) of the wireless slave station to be tested next, and then press SW2. Repeat this procedure till the communication with all wireless slave stations is established and stabilized.
23
ON
23
X10
X1
X10
SW1
1234
SW1
ON 1234
Master station
W NODE
901
901
78
78
78
456
X10
SW2 RUN TEST SET
78
X10
SW3
ON 12345678
74
456
456
456
456
456
456
456
X1
W CH
901
23
23
X1
901
X1
23
23
Confirmation Test
Section 5-3
5-3
Confirmation Test
This test is for checking the wireless communication status with each slave station in the system in operation after installation. The test can be implemented by the switching operation from the master station.
5-3-1
Preparation
· The DeviceNet master does not need to be connected for the confirmation test. (The DeviceNet slave needs to be connected. ) · The confirmation test is employed for the inspection work after installation. · Leave the mode select switches of the wireless slave stations in the "Run" position.
5-3-2
Test procedure
Master station
W NODE
901
901
X10
X1
901
SW2 RUN TEST SET
78
W CH
901
X10
X1
SW3
ON 12345678
1. Set the mode select switch of the wireless master station to "TEST", and the WNODE switch to the WNODE number of the wireless slave station to be tested. Set SW3 to "bit 5 = ON".
78
78
78
456
23
23
23
Master station
MS NS WS
N NODE
901 901
78
23
X10
X1
SW1
ON 1234
RUN TEST SET
78
Master station
MS NS WS
N NODE
901 901
78
23
X10
X1
SW1
ON 1234
RUN TEST SET
78
456
456
23
456
23 23
SW2
2. Turn on the communication power supply to the wireless master station. The NS LED goes off and the MS LED flashes green.
456 456
456 456
SW2
3. [. . . ] !Caution To prevent electric shock when replacing a unit, be sure to turn OFF the power supplies to all of the nodes (master and slaves) before removing the faulty unit.
153
Appendix A
Device Profiles
Refer to the specifications and device profile in this manual when connecting an OMRON DeviceNet wireless master station to another company's master.
Device profile of DeviceNet wireless unit master station (WD30ME/-ME01)
General data Applicable DeviceNet Specifi- Volume I-Release 2. 0 cations Volume II-Release 2. 0 Vender name OMRON Corporation Device profile Product catalog number Product revision Physical conformance data Network current consumption Connector type Physical insulation Supported indicator Slaves : Communication Adapter Manual number 1. 0 Open plug Yes Module Network Wireless Rotary switch 0 DIP switch Vender ID = 47 Device profile = 12
MAC ID setting Default MAC ID Transmission communication speed setting Supported transmission communication speeds Communications data
125 kbps 250 kbps 500 kbps Predefined Master/Slave con- Group 2 only server nection set Dynamic connection support No (UCMM) Explicit message fragmentation support Yes
155
Device Profiles
Appendix A
Object Loading
Identity Object (0 x 01)
Object class Attribute Service Attribute Not supported Not supported ID content 1 Vendor 2 Product type 3 Product code 4 Revision 5 Status (bits supported) 6 Serial number 7 Product name 8 State Service DeviceNet service 05 Reset OE Get_Attribute_Single Get Set Value 47 12 505 3. 02 Unique for each unit Bit 0 only WD30-ME-V1
Object instance
Parameter option No No
Message Router Object (0 x 02)
Object class Object instance Vender fix specification addition Attribute Service Attribute Service Not supported Not supported Not supported Not supported No
DeviceNet Object (0 x 03)
Object class Attribute Service Attribute Not supported Not supported ID content 1 MAC ID 2 Communication speed 3 BOI 4 Bus-off counter 5 Allocation Information 6 MAC ID switch changed 7 Communication speed switch changed 8 MAC ID switch value 9 Communication speed switch Service DeviceNet service 0E Get_Attribute_Single 4B Allocate Master/ Slave_Connection_Set Release_Master/ Slave_Connection_Set Get Set Value
Object instance
00H
Parameter option No No No
156
Device Profiles Connection Object (0 x 05)
Object class Attribute Service Max. number of active connections Object instance 1 Section Instance type Production trigger Transport type Transport class Attribute Not supported Not supported 1
Appendix A
Information Explicit Message Cyclic Server 3 ID content 1 State 2 Instance type 3 Transport class trigger 4 Produced connection ID
Max. number of instances 1
Get
Set
Value 0000H 8300H
5 Consumed connection ID 6 Initial comm. characteristics 7 Produced connection size 8 Consumed connection size 9 Expected packet rate 12 Watchdog time-out action 13 Produced connection path length 14 Produced connection path 15 Consumed connection path length 16 Consumed connection path Service DeviceNet service 05 Reset 0E Get_Attribute_Single 10 Set_Attribute_Single
2100H FF00H FF00H 0100H 0000H
0000H
Parameter option No No No
157
Device Profiles
Object instance 2 Section Instance type Production trigger Transport type Transport class Attribute Information Polled I/O Cyclic Server 2 ID content 1 State 2 Instance type 3 Transport class trigger 4 Produced connection ID Get Set
Appendix A
Max. [. . . ]