[. . . ] In Focus Corporation: 27700B SW Parkway Avenue · Wilsonville , Oregon 97070-9215 Phone: 503-685-8888 · 1-800-294-6400 · Fax: 503-685-8887 In Europe: Olympia l · NL-1213 NS Hilversum, The Netherlands Phone: (31) 35 6474000 · Fax: (31) 35 6423999 Freephone: 008000 4636287 (008000 INFOCUS) In Asia: 238A Thomson Road · #18-01/04 Novena Square Singapore 307684 · Telephone: (65) 334-9005 · Fax: (65) 334-4525
User's Guide 010-0298-00
Part No. 010-0298-00 DP6860 User's Manual. qxd Printed in Japan
010-0298-00
QR50271
w w w. c o m 1. 800. 294. 6400
DP6860 Desktop Projector
P R ESEN TAT I ON SOL U T I ON S
Liquid Crystal Projector
Thank you for purchasing this liquid crystal projector. WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S GUIDE" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. [. . . ] Center Down Up ( Center )
ASPECT
-
Select Image Aspect Ratio: 4:3[ ] 16:9[ ] 4:3 small[ Select Position of Image : Press the button while 16:9[ ] / 4:3 small[ is selected. Center Down Up ( Center )
] ]
-
-
· 4:3 small may not be displayed correctly with some input signals.
ENGLISH-12
OPERATIONS (continued)
The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The functions indicated (**) are effective on video input mode only, not on RGB input mode, except in the P. IN P. Input Menu Item Description
Automatic Adjustment at RGB Input: Select the EXECUTE with the button. Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE), and horizontal size (H. SIZE) are automatically adjusted. Automatic Adjustment at Video Input: Select the EXECUTE with the button. A signal type appropriate for the input signal is selected automatically when EXECUTE is selected automatically. Valid only when AUTO is set for VIDEO on the menu.
· This operation requires approximately 10 seconds. · This function is the same as for the AUTO function in Basic operation.
AUTO
RGB
Displays RGB Input Frequency: Displays the horizontal and vertical sync signal frequencies for RGB input.
· Valid only at RGB input.
Select Video Signal Type: Select the signal type with the and buttons. Select NTSC, PAL, SECAM, NTSC4. 43, M-PAL, or N-PAL as appropriate for the input signal. The selection of AUTO enables and executes the function AUTO (Automatic Adjustment at Video Input), except for the N-PAL input. VIDEO (**)
· Use this function when the image becomes unstable (eg. Pressing the AUTO button in this case may correct this problem except for the N-PAL input. · For the COMPONENT VIDEO input, this function is not effective and the signal type is distinguished automatically. Menu for the signal of HDTV.
VIDEO NR (**)
Progressive (**)
Set/Clear Noise Reduction Mode: Select the TURN ON / TURN OFF with the / button. When the TURN ON is selected, the NR mode is active and the noise on screen of the video input will be reduced. Select Progressive Mode: Select the mode suitable for the input signal with the and buttons. The TV mode and the CINEMA mode convert the interlaced video signal into the progressive signal. The CINEMA mode is adptable for 2-3 Pull-Down system.
· Use this function to raise resolution, at the interlaced video input except HDTV signals.
BLACK(**)
Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF with the / button. When the TURN ON is selected, the black enhancement mode is active and the contrast ratio of the screen for the video input will be raised by making black level darker.
ENGLISH-13
ENGLISH
Input Menu
OPERATIONS (continued)
Image Menu
The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start operation.
SETUP INPUT IMAGE OPT. [. . . ] Switch power OFF immediately and replace the lamp as shown in P. 17~18 "Lamp". The horizontal or vertical frequency of the input signal is not within the specified range. Check the specifications of the equipment and the signal source.
*1)
CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. NO INPUT IS DETECTED ON ***
SYNC IS OUT OF RANGE ON ***
NOTE *1) This message is cleared automatically after approximately three minutes, and appears every time power is switched ON.
ENGLISH-20
TROUBLESHOOTING (continued)
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. [. . . ]