[. . . ] 8 HOW TO SET UP YOUR NEW HITACHI COLOR TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 HOOK-UP CABLES AND CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 FRONT PANEL CONTROLS FOR 32FX41B AND 32UX51B . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 FRONT PANEL JACKS AND CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Every subsequent press of this button will add 15 minutes to the timer, up to a maximum of three hours. 3 MENU, CURSOR Buttons All On-Screen Display features can be set or adjusted by using these buttons. The CURSOR buttons will highlight functions or adjust and set different features when MENU is pressed. CURSOR buttons will also give you access to FAMILY FAVORITE On-Screen Display. 4 CHANNEL SELECTOR Buttons Enter two or three numbers to select channels. For channels 100 and above, press the "1" button and wait for two seconds before pressing the last two digits of the channel. Channel selection may also be performed by pressing CH up ( ) or down ( ). You may also use these buttons for channel scanning. Press and hold the CH up ( ) or down ( ) buttons and the TV will start quickly scanning through the channels. Release the CH up ( ) or down ( ) buttons when the TV scans to the channel you wish to watch and the TV will tune to that channel. NOTE: The TV may not receive some channels if you are not in the correct SIGNAL SOURCE mode. (See page 39. ) 5 INPUT Button The INPUT button will select between both (only antenna A signal for the 36CX35B model) antenna signals and the four sets of video input jacks each time the button is pressed. When the cyan background is on the lower channel display, channel tuning is for the PIP sub-picture. This method of picture tuning is the same for one antenna input (ANT A only) and two antenna inputs (ANT A and ANT B). PICTURE-IN-PICTURE (PIP) - 21 - 1 PIP button (except 36CX35B) Press the PIP button and a sub-picture appears in one corner of the screen. Use the PIP CH button to select between main and sub-picture tuning control (indicated by the cyan background on the channel numbers). Press the INPUT button when subpicture channel tuning is being controlled, to change between VIDEO: 1, 2, or 3, and ANT A antenna source (ANT B source cannot be viewed as a sub-picture). NOTE: Model 36CX35B does not incorporate Dual Tuner technology. When PIP is displayed, the CURSOR button will not activate the FAMILY FAVORITE menu. 2 PIP button (Model 36CX35B only) Press the PIP button and a sub-picture appears in one corner of the screen. Press the button a second time to remove the sub-picture from the screen. The TV channel will always be either the main picture or the subpicture. PICTURE-IN-PICTURE (PIP) - 22 - 3 SWAP button If you wish to switch what is being shown on the main picture to the sub-picture, press the SWAP button. NOTE: The SWAP function will not operate if ANT B input is set as the main channel (ANT B input cannot be displayed as a sub-picture. ) Model 36CX35B does not have ANT B input. 4 MOVE button To move the sub-picture to another corner, press the MOVE button. The sub-picture moves one step counter-clockwise every time the MOVE button is pressed. (Example below illustrates the MOVE operation for initial shipping conditions. [. . . ] Do not subject the remote control to shocks such as dropping it on the floor, etc. Avoid placing the remote control in a high humidity place or getting it wet. Excessive heat or moisture may cause the unit to cease operation. RECEPTION PROBLEMS - 45 - When the batteries run down, remote control operation will become erratic or possibly stop altogether. Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp, resulting in a distorted picture. RECEPTION PROBLEMS · IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. [. . . ]