[. . . ] When working outside, the use of rubber gloves and non-slip shoes is recommended. If work
the electric tool/machine is not in use, prior to cleaning and maintenance work and when changing a drill bit, saw blade or insert tools of any kind. before switching on that the key or adjusting tools have been removed.
any parts are broken, whether all other parts work properly and are fitted correctly, and make sure that all other conditions which can influence operation and running of the electric tool/machine are as they should be. Damaged guards and protective devices and parts must be repaired properly by an authorized service workshop or replaced provided that nothing else is stated in the operating instructions. [. . . ] ers. ) Note: Drilling without dust removal could permanently damage or destroy the diamond core bit.
The water swivel is connected by way of a Gardena coupling. The water supply valve () can be regulated using the index finger (). The flow of water is displayed by the flow indicator. Note: If wet-drilling core bits are allowed to run dry, they will become overheated, which could lead to destruction of the diamond segments.
Insert the core bit into the chuck, possibly turning it slightly until the longitudinal groove can be felt to lock in place. to remove the core bit, first slide back the locking sleeve and then pull out the core bit. 17
Speed-change switch
Important: Wet and dry-drilling core bits are designed for a drilling contact pressure of 250 N (25 kg). Insufficient pressure can lead to polishing of the segments and a reduction of drilling performance. 51343/3).
Water collector
Recommended speeds for maximum drilling performance
Speed (r. p. m. ) Wet (dia. in mm)
Insert the centering ring () for the appropriate core bit diameter into the ring holder ().
3 (3900) 2 (2400) 1 (1200)
825 2032 3082
16 42 35 67 56152
Extraction and water supply Power supply
Dry drilling Vacuum cleaner connection Electric supply as per rating plate
Speed selection Hole-starting aid Core bit
Select correct speed Use centering disc Use DD100-D diamond core bits
Wet drilling Water connection and water extraction Electric supply as per rating plate Safety device according to national approval for the use of this hand-held electric tool Select correct speed Use centering ring Use DD100-W core bits
Insert the guide pin () on the water collector holder into the boss () in the side handle collar. Press the frame of the water collector holder into its guide on the side handle collar (). Insert the water collector () and press it down firmly into the holder. Connect the water extraction hose.
Caution: DD-BI-HCW core bits (hand held) must be used for drilling anchor holes!18
If the sealing ring supplied with the diamond core bit begins to leak, it must be replaced. Reordering information: The diameter range is printed on the sealing disc.
5
1 4 2 3
1
OP
EN
CLO S
E
OP
EN
CLO S
E
3
2
Removing a core bit 1. Locking sleeve
Press the core bit through the water collector The water supply valve can be regulated us(sealing disc, centering ring) onto the surface ing the index finger. Switch on the DD 100 by pressing the main switch.
Fitting a core bit 1. Motor unit
Hold the core bit before disengaging the locking sleeve. When the core bit is released, ensure that the core does not accidentally fall out of the bit. When drilling overhead, close the water supply valve and drain the core bit via the water supply hose before releasing it from the chuck.
Important: First-time conversion of a dry-drilling machine (DD100-D, DD100-B) to a wet-drilling (DD100-W, DD100-M) can only be carried out by a Hilti service centre. 19
Safety precautions on the jobsite
Preparations before beginning work
Electrical safety
The PRCD (DD100 wet drilling machine) fault interruptor protects the operator in case of faults in the insulation of the motor unit or supply cord (between the PRCD and the motor unit). This device also prevents the machine from restarting of its own accord when power returns after an interruption in the power supply. The earth/ground connection protects the operator from dangerously high voltages in case of drilling into live cables. The protective function of the ground fault interruptor must be checked at regular intervals in accordance with regulations issued by national authorities.
Before beginning work with the drilling system, read the oper- In addition to the safety precautions, the following preparations ating instructions carefully and ensure that the saftety pre- at the jobsite must be made. In order to ensure safe, trouble-free operation, the drilling Hold the DD 100 firmly with both hands. system must be kept clean. (Do not clean using a jet of wa- Pay attention and concentrate on the job when working. If leakage occurs in the water supply system, the equipment must be serviced.
20
DD100 motor
Technical data
Voltages: Power input: Current input: Frequency: No-load speed: 100/115 V 230/240 V 100V = 1400 W 1700 W 110 V = 1600 W 115 V = 1600 W 15 A 8A 50/60 Hz 50/60 Hz 1st speed: 1200 r. p. m. [. . . ] For repair or replacement, send tool and/or related parts immediately upon discovery of the defect to the address of the local Hilti marketing organization provided. This constitutes Hilti's entire obligation with regard to warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties.
6
1. Press the ON button again before beginning operation.
1 6
2 4
3 5
In the case of a malfunction (test failed), the unit must be checked by an electrical Keep the ventilation slots on the motor housspecialist before work with the equipment ing and side handle clean. Ensure that the extraction head and water swivel interfaces are kept clean. [. . . ]