[. . . ] Lay all three castings on a level surface with the top (smooth) surface downward. NH NH 2-C 2-B NH MG BV BV 2-D Another View of Clip (NH) Right Console Casting 2-A Left Console Casting Hardware shown actual size MG MG (NH) Clip (2) Qty. Alignment Pin BV Alignment Hole Center Console Casting Right Console Casting 2-A. Lay all three castings on a level surface with the smooth (top) surface downward. Hardware shown actual size BV MG (MG) 1/4-20 x 7/8 Hex Head Cap Screw (8) Qty. (BV) 1/4-20 Hex Nut (8) Qty. 2-B. Fasten with four SCREWS (MG) and four HEX NUTS (BV) and one Clip (NH). [. . . ] Level and tighten the casters. 11-A Non-Locking Caster Locking Caster 11-B Hex Collar Base Front 11-A. Use an 11/16" open end wrench to tighten the Hex Collar against the Base Casting. (Pg. 14) Step 12 NOTE: Use a ground cloth to protect the paint finish during this step. Check that all fasteners are tightened before turning the grill Right-Side-Up. Carefully turn the grill Right-Side-Up. 12-A Protect with groundcloth Control Panel this side. Protect with groundcloth Complete Assembly of the Console to the Pedestal. Step 13 EY 13-A View of Inside of Main Burner 13-A. Assemble four HEX NUTS (EY) onto the four studs that protrude through the center burner casting. Tighten all fasteners. Hardware shown actual size (EY) #10-24 Hex Nut (4) Qty. (Pg. Fasten BURNER in place per detail 14-D. Hardware shown actual size 14-A Right Console (JD) #10-24 Stamped Wing Nut (2) Qty. 14-D Burner Valve Tube Burner Tube 14-B Caution: Assemble the wires BELOW the burner tubes! 14-C JD JD 11-D. Tighten all fasteners. Step 15 Assemble the BURNER to the LEFT CONSOLE. Move the Flexible Fuel Hose downward to give clearance for inserting the burner tube. The Flexible Fuel Hose and Wiring must be routed BELOW the burner tube per detail 15-D. Left Console Hardware shown actual size 15-A (JD) #10-24 Stamped Wing Nut (2) Qty. 15-D Valve Tube Flexible Fuel Hose Left Burner 15-B TEST THE IGNITER: A SPARK SHOULD APPEAR AT Flexible Fuel Hose ELECTRODE TIP. Burner Tube IF THE SPARK DOES NOT APPEAR: -CHECK THE WIRE CONNECTIONS TO THE 15-C MODULE. -CHECK PROPER ASSEMBLY OF FRESH 9-VOLT BATTERY. JD JD Caution: Assemble the wires BELOW the burner tubes! 15-D. 18) Assemble the DOOR LATCH to the PEDESTAL. Step 16 16-A KE Door Latch KE 16-A. NOTE: You may have to adjust door latch to insure proper alignment of door latch post. Hardware shown actual size (KE) #6-32 x 3/8 Self-tapping Screw (2) Qty. Assemble the DOOR HANDLE to the DOOR. Assemble the DOOR LATCH POST to the DOOR. Step 17 17-A Door Handle 17-B Door Latch Post LF KE KE LF 17-A. Attach the DOOR LATCH POST to the DOOR with two SCREWS (CW). Hardware shown actual size Hardware shown actual size (LF) #8-32 x 1/2 Self-tapping Screw (2) Qty. (KE) #6-32 x 3/8 Self-tapping Screw (2) Qty. (Pg. Adjust the DOOR LATCH on the PEDESTAL for proper door closure. Step 18 18-A Door GA (4) Places Door Latch 18-A. Attach the DOOR to the PEDESTAL with four SCREWS (GA). Hardware shown actual size 18-B. Tighten all fasteners. (GA) #10-24 x 3/8 Flat Head Screw (4) Qty. Assemble the MAIN BURNER LID. Adjust the DOOR LATCH on the PEDESTAL for proper door closure. Step 19 19-A 19-B IC HB HB IC IC HB 19-A. Hardware shown actual size (HB) 3/16 Dia x 1-3/16 LG Clevis Pin (2) Qty. (IC) Hair Pin (2) Qty. (Pg. [. . . ] This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province. You can find the nearest authorized Coleman service center by calling 1-800-356-3612. If a service center is not conveniently located, you may call the same number for instructions on shipping the product to the Coleman Company, Inc. You may also call the same number if you have any questions concerning this warranty. [. . . ]