[. . . ] CAUTION - Indicates a potentially hazardous situation, which, if not avoided, may result in minor/moderate injury or product/property damage. It also alerts against unsafe practices.
The Lightning Flash CAUTION: TO REDUCE The exclamation And Arrow Head THE RISK OF ELECTRIC point within the Within. SHOCK, DO NOT triangle is a warning The triangle is a REMOVE COVER sign alerting you of warning sign (OR BACK). NO USER important alerting you of -SERVICEABLE PARTS instructions "DANGEROUS INSIDE. [. . . ] To remove the tab, pull it in the direction of the arrow in the illustration as shown:
When the operation of the remote control becomes unsatisfactory, replace the original battery with a new 3-volt lithium battery. Place one 3V CR2025 battery into the battery holder, observing the positive (+) direction. If the battery is placed incorrectly the remote control will not work. Note: Please remove all of the batteries to prevent damage or injury from possible battery leakage if the unit is not to be used for a long period of time. . Use only the specified size and type of battery.
-8-
Operating Instructions
Make sure the AC power cord from this unit is properly connected to a 240V 50Hz household AC power outlet. Make sure the AC power cord from this unit is properly connected to a 240V 50Hz household AC power outlet.
) Setting the Clock
1) While the unit is at STANDBY mode, press and hold MODE button on the top panel or the remote control for 2 sec. "12H" will show and flash on the display indicating that the clock is set to 12 hour format. 2) Press TUNE/SKIP button on the top panel or remote control once to change the clock format to 24 hour time. The display will change from "12H" to "24H" .
3) Press the MODE button to confirm. Press TUNE/SKIP button on the top panel or remote control to set the hour. Press TUNE/SKIP button on the top panel or remote control to set the minute. Press MODE button to confirm.
-9-
Operating Instructions
) SETTING 1 or 2 ALARMS
You can only set your Alarm mode at Standby mode.
A. Set Alarm 1 1) While the unit is at STANDBY mode, press and hold ALARM 1 button on the top panel for 2 sec. Press "ALARM 1" button to confirm.
2) Minute digit will begin flashing, press "TUNE/SKIP" button to set the minute. 3) Wake up mode display will begin flashing, press TUNE/SKIP to select the below: a: Wake up to Radio : "FM Broadcasting"You have to pre tune your desired radio channel in FM radio mode before setting the wake up function. b: Wake up to Radio: "AM Broadcasting You have to pre tune your desired radio channel in AM radio mode before setting the wake up function. c: Wake up to iPod playback d: Wake up to Buzzer For Radio Broadcasting and IPOD playback, the default volume is 10 and will increase to 16 gradually. If the wake up mode is set to iPod playback with no iPod connected, it will become Buzzer alarm.
B. and repeat the above 1), 2) & 3) steps in Set Alarm 1 to set ALARM 2.
- 10 -
Operating Instructions
C. Snooze Function After alarm is ON, you can press SNOOZE and ALARM1 / ALARM2 buttons on the top panel or remote control to temporarily deactivate the alarm which will activate again after 9 minutes lapse. Sleep Function When unit is power on, Press SLEEP button on the top panel or remote control, 2:00 and sleep indication will ON. Press SLEEP button again to change and select from 2:00 to 1:30, 1:00, 0:30, 0:20, 0:10 or 0:05. [. . . ] - Remove batteries, disconnect the unit from the main power supply for 5 minutes. If this does not help, leave the unit unplugged before seeking advice. Replace all of them together Use the recommended type.
- 16 -
iPod Won't play iPod files or will not function as expected.
- Make sure the function is set to iPod mode. - Vibrations may have caused the iPod to come loose from the docking station. [. . . ]