[. . . ] Wide Format Printer
Operation Guide
Please read the Operation Guide before using the printer. Keep it in the designated location for easy reference.
As an ENERGY STAR Partner, KYOCERA MITA AMERICA, INC. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. registered mark.
NOTE
· This Operation Guide applies to models KM-P4845w and KM-P4850w. [. . . ] To continue printing press the On Line key once more to place the printer online.
10
Grasp the paper roll insertion latches and close the paper roll insertion cover securely.
3-8
CHAPTER 3 GETTING READY FOR PRINTING
(3) Dew prevention heater
If the humidity is high (more than 70 %RH) or drastic temperature change occurs, turn on ( l ) the dew prevention heater switch when using the machine. Even if the main switch is off ( ), the dew prevention heater switch can be on ( l ).
(4) How to Use the Paper Tray Support Plate
Set the paper tray support plate based on the paper to be used for printing.
1
Incline the paper tray support plate and slide it to the size indication on the size label of the paper tray.
IMPORTANT When using vellum or film, be sure to turn off ( O ) the dew prevention heater switch. If not, paper may be wrinkled or curled.
2
After setting the paper tray support plate to the desired size, return it to a horizontal state.
3
Follow the same procedure to set the other paper tray support plate to the same height. Depending on the paper to be used and the environment, the support plate may not be contained at the position of the size label. In this case, adjust the position of the paper tray support plate upward or downward.
3-9
CHAPTER 3 GETTING READY FOR PRINTING
3-10
CHAPTER 4
PRINTER OPERATION
1. Basic printing
Perform this procedure in order to send commands to the printer from your computer.
1
Turn the main switch on the printer ON ( | ). The printer will begin to warm up and "Ready to print. " will be displayed once warm-up is complete.
CAUTION
2
Make sure that the Ready indicator is lit.
If the printer will not be used for a short period of time (overnight, etc. ), turn the main switch OFF ( ). If it will not be used for an extended period of time (vacations, etc. ), remove the power plug from the outlet for safety purposes during the time the printer is not in use.
3
NOTE
Perform the appropriate printing procedure on your computer.
Refer to the Functions Edition (On-Line Manual) for more detailed information on printing from your computer.
4-1
CHAPTER 4 PRINTER OPERATION
2. Printing with manually fed media
When printing through the bypass slot, perform the following procedure.
3
NOTE
Perform the appropriate printing procedure on your computer.
NOTE · Only one sheet of paper can be set onto the bypass table at a time. If the curling persists, place the paper with the curled surface up.
Refer to the Functions Edition (On-Line Manual) for more detailed information on printing from your computer.
1
Adjust the bypass guides to the paper size indications on both sides of the bypass table.
4
When the message "Set paper. bypass" appears, refer to Step 2 and set the next sheet onto the bypass table. Repeat this procedure to set sheets one at a time onto the bypass table until the required number of sheets has been loaded and printed.
2
Set the paper face down all the way into the feed slot aligned with the paper size indication. When placing paper in the bypass table, set the paper quickly all the way into the feed slot. If the paper is set obliquely, pull the paper out and then insert it again.
4-2
CHAPTER 4 PRINTER OPERATION
3. Making a Test Print
Perform this procedure to send a test print command from the printer's operation panel.
7
Press the N or M key to select "2. Inch specifications
NOTE In order to make a test print, you must place a sheet of 8 1/2" x 11" [A4] paper onto the bypass table in portrait orientation.
Set printer: 2. Test print
Metric specifications
Set printer: 2. Test print
1 2
Refer to "2. Printing with manually fed media" (Page 4-2) and place an 8 1/2" x 11" [A4] sheet of paper onto the bypass table in portrait orientation. A test print will be automatically output.
Making a test print from the Web Manager interface It is possible to use an Internet Web browser on a client computer to access the Web Manager interface and print out a list of setting information. For a more detailed explanation, refer to the Functions Edition (OnLine Manual).
3
Press the N or M key to select "2. Inch specifications
Menu: 2. Set/user.
Metric specifications
Menu: 2. Set/user
4 5
Press the Enter key. Inch specifications
Set/user: 2. Set printer
Metric specifications
Set/user: 2. Set printer
6
Press the Enter key.
4-3
CHAPTER 4 PRINTER OPERATION
4. Canceling Printing
If "Processing data. " or "Printing" ["Now printing. "] is shown in the message display, press the Stop key. [. . . ] 600 dpi x 600 dpi Developing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dry Toner supply system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bottle cartridge system Fixing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heat roller Cleaning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]