[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] When the monitor is connected to the S Video jack, change the "OSD Output" setting to "S Video. " 1. Press the MENU button on the front panel or SETUP button on the remote controller. Use the and cursor buttons to select "OSD Output" and then use the and cursor buttons to select "S Video. " 4. Press the ENTER button. The speaker configuration menu appears. * Menu ***************** 1. Speaker Config 1. Speaker Config 2. Speaker Distance *********************** 3. Level Calibration 4. Input Setup a. Subwoofer :Yes 5. OSD Setup b. Front :Large 6. Preference c. Center :Large d. Surround :Large e. Surround Back:Large f. Crossover : 80Hz Quit:|SETUP| 36 Configuring the speakers 4. Use the and cursor buttons to select "Subwoofer" and then use the and cursor buttons to select the subwoofer setting. No: Select when a subwoofer is not connected. TX-8211/700E/600/600E Remote controller 9. Use the and cursor buttons to select "Crossover" and then use the and cursor buttons to select the crossover frequency mode setting. Adjustable Crossover (80/100/120 Hz) for Bass Management This setting allows you to set the crossover frequency for your speaker system. This setting is valid when "Subwoofer" is set to "Yes, " or for speakers that are set to "Small, " at the "Speaker Config" menu. The crossover frequency is the minimum frequency delivered to a speaker and can be set to 80 Hz, 100 Hz, or 120 Hz. Frequencies below this are cut from speakers set to "Small" and sent to the subwoofer (or to speakers set to "Large"). The "Level Calibration" menu appears. * Menu ***************** 1. Speaker Config 2. Speaker Distance 3. Level Calibration 4. Input Setup 5. OSD Setup 6. Preference * Menu ***************** 1. Speaker Config 2. Speaker Distance 2. Speaker Distance *********************** 3. Level Calibration 4. Input Setup a. Unit :feet 5. OSD Setup b. Front L/R :12ft 6. Preference c. Center :12ft d. Surround L/R : 7ft e. Surround Back : 7ft |ENTER|Quit:|SETUP| Quit:|SETUP| 2. Use the and cursor buttons to select "Unit" and and cursor buttons to select the then use the desired unit of measure. Use the and cursor buttons to select "Front L/R" cursor buttons to set the and then use the and distance from the front speakers to your normal listening position. Use the and cursor buttons to select "Center" and and cursor buttons to set the then use the distance from the center speakers to your normal listening position. Note: You can only set a distance less than that set for the front speakers and within 5 feet (1. 5 meters) of the front speaker setting. For example, if 30 feet (9 meters) is set for the front speakers, then the center speaker distance can only be set between 25 and 30 feet (7. 5 and 9 meters). Use the and cursor buttons to select "Surround L/ R" and then use the and cursor buttons to set the distance from the left surround and right surround speakers to your normal listening position. Note: You can only set a distance less than that set for the front speakers and within 15 feet (4. 5 meters) of the front speaker setting. For example, if 30 feet (9 meters) is set for the front speakers, then the surround speaker distance can only be set between 15 and 30 feet (4. 5 and 9 meters). * Menu ***************** 1. Speaker Config 2. Speaker Distance 3. Level Calibration 4. Input Setup 5. OSD Setup 6. Preference * Menu ***************** 1. Speaker Config 3. Level Calibration 2. Speaker Distance *********************** 3. Level Calibration 4. Input Setup a. Left : OdB 5. OSD Setup b. Center : OdB 6. Preference c. Right : OdB d. Surr Right : OdB e. Surr Back : OdB f. Surr Left : OdB g. Subwoofer : OdB Quit:|SETUP| |ENTER|Quit:|SETUP| db Note: Speakers that you selected "No" or "None" for in the "Speaker Config" menu will not appear. Use the and cursor buttons to select "Left. " You will hear a pink noise from the front left speaker. 38 Configuring the speakers (1) Remember the volume level of this noise and then press the cursor button. The TX-8211/700E/600/600E will now emit the pink noise from the center speaker. [. . . ] · TV (or monitor) is not set to receive the output signals from the receiver. · Input source is connected to the COMPONENT VIDEO IN connectors. © Make sure TV (or monitor) is connected to COMPONENT VIDEO OUT connectors (see pages 20, 28). 77 Troubleshooting guide If one of the messages shown below appears "Not available with headphones use" Operation not allowed because headphones are plugged into the TXSR700/700E/600/600E. "Not available with Multichannel use" Operation not allowed while the multi-channel output is being used. [. . . ]