[. . . ] Copyright Statement is the registered trademark of Zonet Technology Inc. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Zonet Technology Inc. Without the permission of Zonet Technology Inc. , any individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages. Table of Contents Chapter 1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The default value is 3600. NOTE: To improve security level, do not use those words which can be found in a dictionary or too easy to remember!Wireless clients will remember the WEP key, so you only have to input the WEP key on wireless client once, and it's worth to use complicated WEP key to improve security level. 27 WPS Settings Wi-Fi Protected Setup (WPS) is the simplest way to build connection between wireless network clients and ZSR4134WE. You don't have to select encryption mode and input a long encryption passphrase every time when you need to setup a wireless client, you only have to press a button on wireless client and this wireless router, and the WPS will do the rest for you. WPS Mode: Supports two ways to configure WPS settings: PBC) and PIN code. PBC(Push-Button Configuration): If you want to use PBC, you have to push a specific button on the wireless client to start WPS mode, and switch ZSR4134WE to WPS mode too. You can push WPS button of ZSR4134WE, or click PBC button in the web configuration interface to enable WPS Note: Press WPS button of ZSR4134WE for one second and WPS indicator will blinking for 2 minutes. During the blinking time, you can enable another Router to implement the WPS/PBC negotiation between them. Two minutes later, the WPS indicator will be off. PIN: if you want to use PIN code, you have to know the PIN code of wireless client and switch it to WPS mode, then provide the PIN code of the wireless client you wish to connect to ZSR4134WE. 28 WDS Settings In this mode, you can expand the scope of network by combining up to four other access points together, and every access point can still accept wireless clients. WDS Mode: Lazy Mode: You need to configure ZSR4134WE's BSSID into another device, but don't need to input another device's BSSID in ZSR4134WE, and they will connect together automatically. Bridge Mode: You can wirelessly connect two or more wired networks via this mode. In this mode, you need to add the Wireless MAC address of the connecting device into ZSR4134WE's AP MAC address table or select one from the scanning table. At the same time, the connecting device should be in Lazy, Repeater or Bridge mode. Repeater Mode: You can select the mode to extend the distance between the two WLAN devices. Functioning as a WDS repeater, ZSR4134WE connects to both a client card as an AP and to another AP. In typical repeater applications, APs connecting to other APs equipped with WDS functionality must also support WDS. In this mode, you need to add the MAC address of the connecting device into ZSR4134WE's AP MAC address table and the connecting client should be in Lazy, Repeater or client mode. Encrypt Type: You can select from WEP mode, TKIP mode, AES mode for security here. Pass phrase: Enter the key, the key format according to encryption you selected. AP MAC: Input the MAC address of another wireless router. NOTE: Two wireless routers must use the same band, channel number, and security setting. 29 Advanced Wireless Settings ZSR4134WE provides some advanced control of wireless parameters, if you want to configure these settings, please click "Wireless" menu on the left of web management interface, then click "Advanced Settings", and the following message will be displayed on your web browser: BG protection Mode: Auto by default. Basic Data Rates: For different requirement, you can select one of the suitable Basic Data Rates. Do not modify default value if you don't know what it is, default value is 100. Do not modify default value if you don't know what it is, default value is 2346. Do not modify default value if you don't know what it is, default value is 2347. Unless you're using ZSR4134WE in a really big space, you may not have to set output power to 100%. [. . . ] I Can not login to the Web interface of ZSR4134WE after entering the IP address in the address field Step 1: check ZSR4134WE if it works well. Once the device is powered on for a few seconds, the SYS indicator on the panel will be turned on. Step 2: check the network cable if it is work and the corresponding indicator is "Always ON". Sometimes, the indicator is "Always ON", but it does not mean it gets through. [. . . ]