[. . . ] If the hot water system has not been used for such a period, turn on all hot water faucets and let the water flow from each for several minutes before using the washing machine. Do not smoke or use an open flame during this time, the gas is flammable.
~ GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. [. . . ] Desclaing the washer If the correct amount of detergent is dispensed, the machine should not need to be descaled. If the washer needs to be descaled, use a descaling agent with corrosion protection. Use as directed on the packaging.
Cleaning the washer
^ Clean the exterior of the washer with a mild solution of non-abrasive detergent or soap and water. ^ Clean the drum with a stainless steel cleaner specially formulated for use in a washing machine. This type of cleaner is available from Miele.
24
Cleaning and Care
Cleaning the detergent drawer
Detergent residue should be cleaned out regularly.
^ Pull the detergent drawer out as far as it will go. Press down on the red release lever and pull the drawer out of the machine. Remove the siphon tube from the fabric softener compartment § and rinse under warm water. Replace the siphon tube.
, Do not use chemical solvents, abrasive cleaners, glass or all purpose cleaners. These can damage plastic surfaces and other parts.
25
Cleaning and Care
Cleaning the drain pump and lint trap
Occasionally, small objects (buttons, coins, etc. ) may become trapped in the lint trap. If the machine does not drain completely, the lint trap should be checked to ensure that it is free of foreign objects. ^ Turn off the appliance with the "On / Off" button.
, Caution: If laundry has been washed at a high temperature, the water draining out of the machine will still be hot!Handwash / Options: Extended, Heavy soil, Sensitive Temperatures: Warm B, Cold A, No Heat e Spin speed: Med Items: For hand washable items with no wool or silk content. Sturdy Options: None Temperatures: Warm B, Cold A, No Heat e Spin speeds: Med, Low Items: For a quick, mixed load of colorfast items. Custom Options: Extended, Heavy Soil, Soak, Sensitive Temperatures: Sanitize F, Very Hot E, Hot D, Very Warm C, Warm B, Cold A, No Heat e Spin speeds: Max, High, Med, Low, Slow, Hold, No Spin Items: All options can be selected individually for colorfast or white items.
Cleaning and Care
Once the flow of water stops:
^ Remove the lint trap lid. ^ Remove any foreign objects or lint from the filter.
^ Check that the impeller (in the back of the chamber) rotates freely by spinning it with your hand. ^ Return the lint trap and tighten into place.
, If the lint trap lid is not tightened securely, water will leak out when the machine is used.
27
Cleaning and Care
Cleaning the water inlet filters
The washer has two water inlet filters to protect each inlet valve. These filters should be checked every 6 months and cleaned, if necessary. (This may need to be performed more frequently with some water supplies).
, Inspect the hose regularly. The hose should be replaced if there are cracks in the surface, or if it has been otherwise damaged or cut.
Cleaning the filter in the inlet valve
^ Using a wrench, carefully loosen and remove the plastic hose connector on the inlet valve. ^ Using needle nose pliers, remove the plastic filter (see illustration). Both filters must be put back in place after cleaning.
Cleaning the inlet hose filter
^ Turn off the water valve. ^ Unscrew the inlet hose from the valve by turning the connector counterclockwise using a wrench if necessary.
^ Remove the rubber seal, 1, from the connector. [. . . ] Replace the hose only with a genuine Miele hose, or with a hose able to withstand up to 145 psi (10 bar) pressure. The water valve connector must also be able to withstand 145 psi (10 bar).
, The bolted connection is under water pressure. Adjust the rubber seal and the bolted connection if necessary.
To protect the inlet valve, the two filters (one at the pressure hose / valve connection and one at the inlet connection to the solenoid valve) must not be removed. Hose extension (optional accessory) Hose extensions with a length of 8' 2 7/16" to 13' 1 ½" (2. 5 to 4 m) are available from your Miele dealer or Miele.
47
Plumbing
Water connection
^ Connect the cold water intake hose (blue mark) to the cold water valve and the hot water intake hose (red mark) to the hot water valve. [. . . ]