[. . . ] Operating system independence Interconnect flexibility Fibre Channel fabric switches provide full direct connectivity between all ports on a network, which can increase the total throughput of all devices on a network.
· · ·
FC310 Router Operation
0
Once the FC310 Router SCSI to Fibre Channel option is installed and tested, the library operates exactly as a ATL M1500 library with a SCSI host interface. User operation of the library via the graphical user interface (GUI) panel is unchanged.
Introduction
3
Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002
Key to Successful Configuration of the FC310 Option 0
The FC310 Fibre Channel Option must be configured using the homebred FC310 Prism Router Services software. The key to successfully configuring the FC310 Option is to: · Know exactly how the SCSI cabling in the library is configured including how many:
a b
SCSI buses are present in the library SCSI devices are connected to each bus
·
Use the FC310 Prism Router Services software to create a Map file identifying which SCSI devices are electrically connected to which Fibre Channel ports on the FC310 board
Configuration
0
This document describes the ATL M1500 configuration procedure with two tape drives (maximum). [. . . ] It is used by the FC310 to identify the SCSI devices in the library electronically connected to the Fibre Channel port on the board. To create the FC310 Prism Map, perform the following steps:
1 At the screen prompt, type automap 0 and press <Enter>. The
automap command executes.
2 When the ready prompt appears, type saveconfiguration and press <Enter>. 3
When the ready prompt appears, type firmwarerestart and press
<Enter>.
10
FC310 Router Option Configuration
Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002
Figure 5 Automap Screen
Commonly Used FC310 Services Software Commands 0 for the ATL M1500 Library
The FC310 Services Software resides on each FC310 Router board. This software configures the router for use in the Quantum ATL M1500 library through a Command Line Interface (CLI) that is compatible with any PC and a terminal emulation program (such as HyperTerminal or ProComm). For more information on additional commands, syntax, and usage, see FC310 Services Software Commands on page 13.
Commonly Used FC310 Services Software Commands for the ATL M1500 Library
11
Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002
Table 2 Commonly Used FC310 Services Commands
Command
RouteDisplay
Description List the currently mapped Fibre Channel-to-SCSI routes.
Default
Syntax routedisplay routedisplay [fp] routedisplay [online | offline] routedisplay [fp [fl] ] routedisplay [fp [online | offline] ]
SerialPortBaudRate
Set the baud rate for the FC310 serial port (2400, 9600, 19200, 38400, 57600, or 115200). Transfer a firmware image or NVRAM parameter file to or from the router using ZMODEM file transfer protocol. Displays version numbers and other product information for key components within the FC310. When the optional command name is present, detailed command-specific information is displayed. If a firmware restart is required to make the change, the user is prompted to confirm the restart. Several non-immediate commands require a SaveConfiguration before their modified parameters take effect. When such a command is executed an asterisk appears next to the command line prompt.
FC310 Services Software Commands
13
Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002
Command Syntax
0
The following is a list of syntax used to describe command lines: · · · [ ] indicates required entry < > indicates optional entry | indicates choose one entry
List of Abbreviations 0
The following is a list of abbreviations used to describe command lines: · · · · · fpFibre Channel port number (0 - 2) flFibre Channel LUN (0 - 31) sbSCSI bus number (0 - 3) stSCSI target ID (1 - 15) sl SCSI LUN (0 - 7)
Command Listing
0
A list of the currently available FC310 Services Software commands is shown in table 2.
Table 3 Most Common FC310 Services Commands
Command
FcConnMode
Description Set the connection mode for the FC310 to arbitrated loop or pointto-point. If the frame length is not specified, the current frame length is displayed.
Default loop
Syntax set fcconnmode [loop | ptp] get fcconnmode
FcFairArb
enabled
set fcfairarb [enabled | disabled] get fcfairarb
FcFrameLength
2048 bytes
set fcframelength [512 | 1024 | 2048] get fcframelength
14
FC310 Services Software Commands
Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002
Command
FcHard
Description Enable or disable Fibre Channel hard address assignment. Under soft addressing the FC310 loop address is assigned during loop initialization. Set the value used as the FC-AL hard address.
Default hard
Syntax set fchard [enabled | disabled] get fchard
FcHardAddress
port 0 = 3
set fchardaddress [fp [address]] get fchardaddress [fp]
FcSCSIBusyStatus
Specify the SCSI status value returned when the FC310 is unable to accept a SCSI command due to a temporary lack of internal resources. Specify the soft target LUN used by the FC310 when addressed by the host. Valid route change entries are: fp (0-2) fl (0-31) sb (0-3) st (0-15) sl (0-7).
BUSY
set fcscsibusystatus [busy | qfull] get fcscsibusystatus
FibreBridgeName
set fibrebridgename [name] get fibrebridgename set fibrebridgetargetlun [0 - 31]
FibreBridgeTargetLUN
RouteChange (Immediate)
routechange [fp] [fl] [sb] [st] [sl]
RouteOnline
Set the status of a route to online.
set routeonline [fp] [fl] get routeonline [fp] [fl]
RouteOffline
Set the status of a route to offline.
set routeoffline [fp] [fl] get routeoffline [fp] [fl]
RouteDisplay
List the currently mapped Fibre Channel-to-SCSI routes.
routedisplay routedisplay [fp] routedisplay [online | offline] routedisplay [fp [fl] ] routedisplay [fp [online | offline] ]
FC310 Services Software Commands
15
Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002
Command
FcPortList (Immediate) ScsiInitID
Description List the available Fibre Channel ports and their current status. [. . . ] 0 September 2002
Command
SaveConfiguration (Immediate)
Description Save the new configuration. If a firmware restart is required to make the change, the user is prompted to confirm the restart. The user can override the confirmation request by indicating the override value on the command line.
Default
Syntax saveconfiguration < restart | norestart >
Reserve (Immediate)
reserve
Reservation of the FC310 is implicit; once the configuration image is changed by any user of services (Serial/Ethernet/ Etc. , ) the FC310 becomes RESERVED. Performing a SaveConfiguration, RestoreConfiguration or FcRestart RELEASES the FC310 so that other devices may access it. [. . . ]