[. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference in which case the user will be required to correct the interference at his/her own expense. [. . . ] Features · 1/3" Super HAD Color CCD · Resolution of 550TVL (day-time), 600TVL (night-time) · Outdoor bullet style camera with Sunshield · Enhanced sharpness compensation · 0. 05Lux light sensitivity · Built-in Vari-focal Auto iris lens(2. 8~10mm) · Waterproof (IP66) · Simple Focus adjustment · Supply voltage: 24Vac or 12Vdc · Hidden cable-through function 4 3. Specifications Description Image Device Effective Pixels Resolution Sensitivity S/N ratio Electronic Iris White Balance BLC Video Output Built-in Lens Infrared LEDs IR Distance Operation Power Cable length Operating Conditions Dimensions (Dia. x H) Net Weight 1/3" Sony SuperHAD II Color CCD 768 x 494 (NTSC) / 752 x 582 (PAL) 550TVL (Day) / 600TVL (Night) 0. 05Lux(F1. 2@40IRE), 0Lux with built-in 30 Infrared LEDs More than 50dB with AGC off at 50IRE 1/60 ­ 1/100, 000sec (NTSC) 1/50 ­ 1/100, 000sec (PAL) 3, 000°K ­ 8, 000°K Automatic tracking Built-in, Factory set to ON VBS 1. 0Vpp +/-10%, 75ohm 1/3" Vari-Focal, f=2. 8-10. 0mm, F1. 2, DC Auto Iris 30pcs @ 850nm 35M (110') 24Vac(20~28. 8Vac) or 12Vdc (11. 5~30Vdc), 5Watts max 5' (1. 5M) 14 ­ 122 degrees F (-10°C - +50°C), 85% RH Max. (non-condensing) 2. 68" x 8. 66" (68mm x 220mm) 1. 21 lbs (550g) 5 black 4. Supplied Items 1 x Weatherproof D/N Bullet Camera 3 x Mounting screws 3 x anchors 1 x 2. 5mm L-Wrench 1 x Installation and Operating Instructions 5. External Window Sunshield Lock screw for Sunshield Front cover Body Locking screw for radius Locking screw for Tilt-direction Locking screw for Pan-direction Mounting Base Rubber seal 5-2. Internal Infrared LEDs (X30) Lens Hood Zoom adjustment knob Focus adjustment ring 6 5-3. Iris adjustment and Function switches on the Board. Iris Low Iris High S/W 1 Function ELC Default ELC mode. and operating Back light OFF Linear electronic shutter is Set to OFF for auto iris lens Back light compensation is 2 BLC OFF enabled compensation is automatically. N/A Electronic shutter is fixed to Electronic shutter mode follows 6. Installation · Make sure the power is removed before installation. Procedure of installation 1) Locate at the installation position and drill 3 holes for Mount base on the wall. Use MOUNTING TEMPLATE printed on the bottom of the inner packing material as shown in below drawing. 2) Route the power/ video cable from the camera to the monitor location and power outlet. Care should be taken not to damage, kink or expose the cable to a hazardous environment. 7 black 3) Place camera on a pre-drilled position and fix it by using Mounting screws. Direction I: Adjust the camera direction with screw for Pan-direction. Direction II: Adjust the camera direction with screw for Tilt-direction. Direction III: Adjust the camera direction with screw for radius. 6-2. 2) Place the separated Front cover in a safe place away from water & dust. 6) Using your thumb and index finger, turn Focus ring to set the focus. [. . . ] Connect the low voltage section (12VDC or 24VAC) first then plug the AC adapter into the AC outlet to avoid an improper reset from power jitter and damage from the surge voltage after load. 7. Dimensional Drawings (Units in mm) 10 11 black LIMITED LIABILITY WARRANTY Your new Camera is guaranteed to be free from defects in materials and workmanship for a period of three years from the date of purchase. The product must have been used only for its intended purpose, and not been subjected to damage by misuse, willful or accidental damage, caused by excessive voltage or lightning. [. . . ]