[. . . ] Quick stops, excessive force, and uneven surfaces may cause the unit and cart combination to overturn.
11 Power-Cord Protection Power-supply cords should be
routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.
12 Cleaning The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods The power cord of the unit should be
unplugged from the outlet when left unused for a long period of time.
14 Object and Liquid Entry Care should be taken so that
objects do not fall into and liquids are not spilled into the inside of the unit.
6
15 Damage Requiring Service The unit should be serviced
by qualified service personnel when:
6A A unit and cart combination should
A. Objects have fallen, or liquid has been spilled into the
unit; or
7
Wall or Ceiling Mounting The unit should be mounted to a wall or ceiling only as recommended by the manufacturer. Ventilation The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. [. . . ] Tape deck 2 Speakers B
Left
Illustration: AX-570 Parts in shaded area (
) are not present on AX-470.
4
ENGLISH
CONNECTING SPEAKERS
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is, + and markings are observed. If these wires are reversed, the sound will be unnatural and will lack bass. Do not let the bare speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit and/or speakers.
q
q
q
One or two speaker systems can be connected to this unit. If you connect only one speaker system, connect it to either the SPEAKERS A or B terminals. Use speakers with the specified impedance shown on the rear of this unit. Banana Plug connections are also possible (except for Scandinavian models). Simply insert the Banana Plug connector into the corresponding terminal.
How to Connect: Red: positive (+) Black: negative ()
Unscrew the knob. 5mm (1/4") insulation from the speaker wires. ] Tighten the knob and secure the wire.
ABOUT THE ACCESSORY TERMINALS
AC OUTLETS (SWITCHED)
AX-470>
Use these to connect the power cords from your components to this unit. The power to the SWITCHED outlets is controlled by this unit's POWER switch or the provided remote control transmitter's POWER key. These outlets will supply power to any component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the SWITCHED AC OUTLETS is 100 watts.
<Except Australia, U. K. and Europe models of
PRE OUT/MAIN IN terminals
<For AX-570 only>
REMOTE CONTROL (PHONO) connector
If you have a YAMAHA turntable with a terminal for remote control, connect it to this connector by using the cable provided with the turntable. q VOLUME, BASS, TREBLE, BALANCE, LOUDNESS controls and PURE DIRECT switch settings have no effect on the material being recorded.
7
Adjusting the BALANCE control
Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from speaker location or listening room conditions.
Selecting the SPEAKER system
Because one or two speaker systems can be connected to this unit, the SPEAKERS switches allow you to select speaker system A or B, or both at once.
<AX-570>
BALANCE
l 2 3 4 L5 5R 0 l 2 3 4
<AX-470>
SPEAKERS
SPEAKERS
Adjusting the BASS and TREBLE controls
BASS
l 2 3 4 5 5 0 l 2 3 4 2 3 4 5 5 4
Adjusting the continuously variable LOUDNESS control
This control provides compensation for the human ears' loss of sensitivity to high and low-frequency ranges at low volume. This control is adjustable to retain full tonal range at any volume level.
TREBLE
l 0 l 2 3
1
LOUDNESS
l 2 FLAT
30 dB
l0 9
BASS
: Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response.
3 4 5 6 7
Set to the "FLAT" position.
8
TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response.
2
Set to the loudest listening level that you would listen to.
3
LOUDNESS
l 2 3 4 5 6 7 FLAT
30 dB
l0 9 8
Turn so that the desired volume can be achieved.
8
ENGLISH
Using the PURE DIRECT switch
You can enjoy the purest possible sound from your audio sources by setting this switch so that the indicator illuminates. By doing so, the audio signal bypasses the BASS, TREBLE, BALANCE and LOUDNESS controls, eliminating any alterations to the audio signal. * Concerning AX-570 only, the SUBSONIC FILTER switch and the PRE OUT/MAIN IN terminals are also bypassed.
Setting the PHONO switch <For AX-570 only>
Select either MM or MC position depending on your PHONO cartridge, Moving Magnet or Moving Coil type. However, if you use a high output MC cartridge, select MM position.
PHONO
MC
PURE DIRECT
MM
Setting the SUBSONIC FILTER switch <For AX-570 only>
If you set this switch to "ON" position, undesirable ultra-lowfrequency signals caused by turntable rumble or warped records can be cut out without losing sound quality.
SUBSONIC FILTER
ON
OFF
When you listen with headphones
Connect the headphones to the PHONES jack. When listening with headphones privately, set both the SPEAKERS A and B switches to the OFF position.
PHONES
9
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the CD player, tuner, turntable, equalizer, and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also control various functions of each component.
KEY FUNCTIONS For Control of This Unit
PLAY/CUT PHONO
Turns the power on/off.
POWER SKIP PLAY CD
SEARCH
PAUSE/STOP DISC SKIP
PRESET
+ A/B/C/D/E TUNER
DIR A
DECK A/B
DIR B
TAPE 1
Selects input source.
PLAY
TAPE 2
REC/PAUSE
STOP
REC MUTE
PRESET SKIP ON/FLAT EQ VOLUME
AUX
+
Turns the volume level up/down.
For Other Component Control
Identify the remote control transmitter keys with your component's keys. On each key function, refer to the corresponding instruction on your component's manual.
Controls tuner +: Selects higher preset station number. [. . . ] 76 dB CD/TUNER/TAPE/AUX (Input Shorted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 dB
<AX-470>
PHONO MM (5 mV Input Shorted) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 dB CD/TUNER/TAPE/AUX (Input Shorted) (PURE DIRECT; ON) . . . . . . . . . . . . . . . . . . . . . 110 dB Residual Noise (IHF-A Network) (PURE DIRECT; ON). . . . . . . . . . . . . . . . . . . . . . . . . . . 70 µV
<AX-570> . . . . . . . . . . . . . . . . . . . . . 11 kg (24 lbs. [. . . ]