[. . . ] - Very low temperature setting considerably increase power consumption. - Avoid continuous direct air flow on you or a sick person while sleeping. This air-conditioner must used 20°C(min)-43°C(max) outdoor and 20°C(min)~32°C(max) indoor on the temperature range. The appliance is not intended for use by young children or infirm persons without supervision. [. . . ] The temperature can be set within a range from 16°C (60°F) to 32°C (90°F) by 1°C (1°F) Room Air-conditioner 88 ROOM TEMP DESIRED TEMP TIMER AUTO SWING SENSOR FAN TURBO COOLING TEMP MODE FAN SPEED POWER FAN SPEED · Everytime you push this button, It is selected as follow. (High¡Mid¡Low¡High) POWER ON/OFF SWITCH · To turn the unit ON, push this button. To turn the unit OFF, push this button again. AUTO SWING · Everytime you push this button, the auto swing mode is toggled. MODE SELECT · Everytime you push this button, It is selected as follow. (COOLING¡TURBO¡FAN¡COOLING) 8 · REMOTE CONTROL REMOTE SIGNAL TRANSMITTER TIMER/CANCEL · Everytime you push this button, timer is set as follow. (1Hr¡2Hr¡3Hr¡4Hr¡5Hr¡6Hr ¡8Hr¡10Hr¡12Hr¡16Hr¡20Hr ¡24Hr¡CANCEL). After the unit is timed, if this button is pushed, timer is canceled. TIMER/ CANCEL SLEEP SLEEP · SLEEP mode is selected as follow. (L1¡L2¡Cancel) FAN SPEED AUTO SWING MODE FAN SPEED · Everytime you push this button, it is selected as follow. (High¡Mid¡Low¡High) TEMP MODE · Everytime you push this button, it is selected as follow. (COOLING¡TURBO¡FAN¡ COOLING) TEMPERATURE · It is the button to set the room in the desired room temp. can be set within a range from 16°C (60°F) to 32°C (90°F) by 1°C (1°F) AUTO SWING · Everytime you push this button, the auto swing mode is toggled. POWER ON/OFF · To turn the unit ON, push this button. To turn the unit OFF, push this button, again. Do not use the REMOTE CONTROLLER before the lamp lights. If use, the " °F " temperature display can change to " °C " temperature display (only "°F" temperature display model). 9 FUNCTION POWER ON POWER OPERATION 1. `ROOM TEMP' lamp lights. or Push POWER button FAN TURBO COOLING ROOM TEMP DESIRED TEMP TIMER COOLING MODE MODE MODE or Push the `MODE' button until `COOLING' lamp lights. 1. Current room temperature is follows by pushing "MODE" button. In this mode you can change fan speed and desired temperature at FAN ROOM TEMP any time. The desired room temperature is changed within a range from 16°C (60°F) to 32°C (90°F) by 1°C (°F) 1. It display desired room temperature when `TEMP' button is pushed. `DESIRED TEMP' lamp lights. Change desired room temperature TEMP or TEMP FAN ROOM TEMP DESIRED TEMP TIMER Push the `TEMPvw' button. TURBO COOLING 3. After a few seconds, display is changed to current room temperature and `ROOM TEMP' lamp lights. FAN SPEED is changed as follows by pushing "FAN SPEED" button. It displays as follows. or HIGH MID LOW Push the `FAN SPEED' button. After a few seconds, display is changed to current room temperature. FUNCTION FAN MODE MODE OPERATION 1. [. . . ] · Verify main power switch (main circuit breaker) or fuse of the unit is good. · When blocked by curtains, blinds, or furnitures, etc. , the air flow is restricted and cooling performance is affected. · Check with dealer to determine proper unit capacity for application. · Stop noise by allowing water to drain from base fan through drain hole. [. . . ]