[. . . ] j) Object and Liquid Entry - Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer. k) Cleaning The appliance should be cleaned only as recommended by the manufacturer. l) Non-use Periods The power cord of the appliance should be unplugged from the outlet when left unused for long periods of time. m) Damage Requiring Service Only qualified personnel should service this product. [. . . ] When turning off, always reverse this operation by turning off amplifiers, then your mixer, and then input devices.
SPECIFICATIONS
INPUTS: Line: 10k input impedance 90mV rms sensitivity (for 1. 22V output) Mic: 10k input impedance unbalanced 2 mV rms sensitivity (for 1. 22V output) 78mV rms max input Phono: 47k input impedance 1. 8mV rms sensitivity @ 1 KHz (for 1. 22V output) OUTPUTS: Line: 9V rms max Headphone Amp: 0. 5 watt into 47 Distortion less than 0. 01% FREQUENCY RESPONSE: Line: 20 Hz- 22k Hz ±0. 5 dB Line: 20 Hz- 20k Hz ±0. 5 dB Phono: ±1 dB except for controlled attenuation of -3 dB @ 20 Hz to reduce rumble and feedback EQUALIZER: ±12dB @ 63. 250. 1K. 5K. 17KHz POWER CONSUMPTION: 10 Watt typical 15 watt with full headphone output DIMENSIONS: 480mm(W) x 175mm(H) x 95mm(D) 19" (W) x 7" (H) x 4 (D) WEIGHT: 3. 5 kgs, 7. 6 lbs
SIGNAL TO NOISE RATIOS* (vs. maximum output): Line: Better than 96 dB Mic: Better than 78 dB Phono: Better than 87 dB *JIS - weighted
- The Leader in DJ Technology
©1999 Industries -5http://www. numark. com
DM1090X
MIXER FEATURES
2 3 1 8 7 6 10 4 5 11
We have divided this section into various functional blocks: Inputs, Microphone, Crossfader, Equalizer, Outputs, and Headphone Cueing. Input Toggle Switches - select which source will be live to that channel based on what you have connected to the rear panel input section. Mic Gain controls the mic volume for the 1/4" connector on the rear of the mixer. Treble and Bass for fine-tuning the tone of your voice on both mics through the sound system. Replaceable Crossfader - achieves clean segues between channels 2 and 3.
9 14
12
13
6.
EQUALIZER 5-Band Stereo Graphic Equalizer (EQ) compensates for differences in source material sound quality. In ultra-compact mobile systems this EQ can be used to tailor the sound to the acoustical requirements of the room. Faders have a center detent for an accurate "flat" response.
This is a typical "house" EQ curve. Start with this setting if you've never used a graphic EQ before. This is an example of a poor EQ curve because it cuts the output volume down by 612dB. Below is the worst sort of curve to use because you are using EQ to add volume. With exaggerated boost, you can easily run your power amplifiers into "clipping" and damage your speakers.
"Hard left" selects Channel 2 and "Hard right" selects Channel 3. Use the crossfader for fast and seamless segues from one selected channel to the other. Simply unscrew the two large screws that hold it in place, lift it out and disconnect its cable. Re-attach the new crossfader and screw the mounting plate back onto the unit - you're back in business!
GENERAL EQ HINTS
· Boost the 63Hz band for deep bass tones and solid kick drum sound. Use sparingly because this dramatically increases demand on power amplifiers and could drive them into "clipping" . · As a general rule, less equalization is better!
- The Leader in DJ Technology
©1999 Industries -6http://www. numark. com
DM1090X
OUTPUTS 7. Stereo/Mono toggle - adjusts the Master output for stereo or mono operation. Volume Meter- quickly and accurately tracks dB level of audio sent to it from the master fader. It's OK to "tap the red" as long as the red LEDs aren't constantly lit. Proper attention to the meter results in the punchiest possible sound without audible distortion. Channel Cue/Send Assign - are used to route PFL channel audio to the Monitor Section. [. . . ] Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by NUMARK and should not be relied upon. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER. You may also have other rights, which vary from one jurisdiction to another.
RETURN INFORMATION
a) b) c) d) e) f) g) A Return Authorization number must be obtained from Numark through the address or phone numbers below. A copy of the original sales receipt must also be included for the equipment to be repaired under warranty. [. . . ]