[. . . ] EN Instructions for use Dishwasher . en Index 4 6 7 8 9 10 11 14 16 Programme overview . . en Safety instructions Delivery Immediately check the packaging and dishwasher for any damage which may have been caused in transit. Please dispose of packaging material properly: D The corrugated cardboard consists mainly of waste paper. D The polyethylene film (PE) consists partly of secondary raw material. [. . . ] Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard Mixed Delicate Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food Coffee, cakes, milk, sausage, cold drinks, salads very little Amount of food remains Condition of food remains Wash programme a little loosely attached Rinse off if the dishes have been stacked for several days in the dishwasher prior to washing. Intensive Normal 70° 65° Eco 50° Gentle 40° Quick 45° Pre-rinse Programme sequence Pre-rinse 50° Wash 70° First rinse Second rinse Third rinse Rinse-aid 70° Drying Pre-rinse Wash 65° First rinse Second rinse Rinse-aid 70° Drying Pre-rinse Wash 50° Main rinse Rinse-aid 65° Drying Pre-rinse Wash 40° Main rinse Rinse-aid 55° Drying Wash 45° Main rinse Rinse-aid 55° Pre-rinse Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. You will find the appropriate programme information in the introduction. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. Switching on the appliance Close the door. The expected programme duration is indicated on the numerical display 8 . The programme sequence starts automatically. Programme specifications The programme specifications can be found in the summary of instructions. Greater deviations may occur due to: varying amounts of dishes water supply temperature water pipe pressure ambient temperature mains voltage tolerances and the tolerances specific to the appliance (e. g. temperature, amount of water, etc. ) The water consumption values refer to a set water hardness value of 4. Remaining running time display When the appliance has started, the expected programme running time is displayed. The programmed running time is affected by the water temperature, the number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly. As the effect is not detected until a programme is running, the time may be longer or shorter than expected. End of programme The programme has ended when a figure appears in the numerical display 8 . Aqua sensor * * on applicable models The Aqua sensor is an optical measuring device which measures the turbidity of the rinsing water. When the Aqua sensor is active, "clean" rinsing water may be transferred into the next rinsing bath and/or the temperature adjusted. If the turbidity is greater, the water is drained and is replaced with fresh water. 4 litres for utensils which are "less" dirty. Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 1 to OFF. (Does not apply when Aqua-Stop unit has been fitted) Remove dishes, etc. when they have cooled down. 19 en Interrupting the programme Set main switch 1 to OFF. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. In order to continue with the stored programme, set the main switch to ON again. Intensive drying By activating the "Intensive drying" function, the final rinse will produce a higher temperature in all programmes resulting in an improved drying result (please note that higher temperatures might have an effect on delicate items). Switch off the main switch 1 ; the chosen setting has now been stored. Terminating the programme (Reset) Only when the main switch is on: Rotate programme selector to the Reset position. To restart, rotate the programme selector 3 to the required programme. The programme sequence starts automatically. Changing the programme It is possible to change the programme within 2 minutes after you have switched the dishwasher on. Should it be necessary to change the programme after this period, the programme cycle that has already been begun (e. g. The new remaining time displayed is the sum of the remaining time from the preceding programme cycle and the remaining time attributable to the new programme that has been selected. 20 en Additional functions * on some models additional functions 4 Time delay * h. can be set with the buttons. Pre-Soak * The Pre-Soak programme option serves to perform a pre-soak cycle before the main programme. [. . . ] Use only a residual-current-operated circuit-breaker which features the symbol. Only this circuit breaker guarantees compliance with the currently valid regulations. Protection from freezing temperatures If the appliance is installed in a location where there is a risk of freezing temperatures (e. g. in a holiday home), all water must be completely drained out of the interior (see "Transporting the dishwasher"). Turn OFF the tap, disconnect the supply hose and allow to drain. Removing the appliance It is essential, when removing the appliance, to observe the following sequence: First, disconnect the appliance from the power supply. [. . . ]