[. . . ] SMD-426, SMD-427
Supervised Wireless PowerG Smoke / Heat and Smoke Detector 1. INTRODUCTION
SMD-426 (smoke detector) and SMD-427 (heat and smoke detector) are automatic fire detectors with integral audible signal for open area protection, designed to sense heat or smoke (not flame) and fitted with a PowerG type transceiver. SMD-426 / SMD-427 provides early warning of developing fire by sounding an alarm with its built-in alarm horn, and by transmitting a coded alarm signal to a PowerG receiver or to a compatible wireless alarm control panel. SMD-427 will activate a fire alarm upon either smoke or heat (temperature rate-of-rise) condition. [. . . ] If the detector is in any diagnostics mode, the detector performs the diagnostics test as described in section 6. 1.
6. 1 Diagnostics Test
Caution!The diagnostics test cannot be performed while tamper is in "open" state. When the LED lights orange (red and green), this indicates correct operation of the LEDs.
D-302894
5
C. Note: If the detector is not in local diagnostics or installer diagnostics mode, the detector will not perform the link quality test. LED response Green LED blinks Orange LED blinks Reception Strong Good
LED response
Reception
Red LED blinks Poor No blinks No communication IMPORTANT!If you receive a "poor" signal from the detector, re-locate it and re-test until a "good" or "strong" signal strength is received. Note: For detailed Diagnostics Test instructions refer to PowerMaster-10 Installer Guide.
7. Align bracket tabs with the detector slots and rotate the detector as shown. A battery must be inserted into the detector before the detector can be mounted onto the bracket. Unauthorized removal of the unit from the bracket will initiate a tamper alert!
A B D C
1
2
8. This smoke detector is designed for use in a single residential unit or offices, which means that it should be used inside a single family home or apartment or office. Please refer to NFPA 101, the Life Safety Code, NFPA72 for smoke detector requirements for fire protection in buildings not defined as "households". The smoke detector will not sense a fire if the smoke does not reach the sensor. In order for a smoke detector to sense smoke, it must be installed in the immediate vicinity of the fire. In addition, smoke from fires in chimneys, in walls, on roofs, in remote parts of the building, or on another level from where the smoke detector is located, may not reach the smoke detector quickly enough for occupants to escape unharmed. For this reason, installer shall install smoke detectors on every level, in every sleeping area and in every bedroom of the household. The alarm horn in this smoke detector meets or exceeds current Underwriter's Laboratories standards. However, if the smoke detector is not located in the same room as the occupant or if it is blocked by a closed door or normal noise, the alarm horn may not be heard. In addition, sound sleepers, or persons who are under the influence of drugs or alcohol may not hear the alarm or be able to react to it. Therefore, locate this smoke detector, which has a sounder rated at 85 dB at 10 feet, on every level, in every sleeping area and in every bedroom of the household. This detector, if used as a stand-alone unit, will not alert people who are hard of hearing. In general, detectors may not always warn you about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson. [. . . ] THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER'S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION. However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer. When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of. [. . . ]