[. . . ] SVM-08020 SERVICE MANUAL SPLIT TYPE Indoor Unit <High Wall, Heat Pump Type> Outdoor Unit <Heat Pump Type> RAS-107SKV-E RAS-107SAV-E R410A March, 2008 FILE NO. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REFRIGERANT R410A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] AUTO RESTART OPERATION To automatically restart the conditioner after the power failure (Power of the unit must be on. ) Setting 1. Press and hold the RESET button on the indoor unit for 3 seconds to set the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 secpmds) Do not operate ON timer and OFF timer. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the operation. Name and Functions of Indications on Remote Controller [Display] All indications, except for the clock time indicator, are displayed by pressing the button. 1. Transmission mark This transmission mark indicates when the remote controller transmits signals to the indoor unit. (AUTO, COOL, DRY and HEAT) Temperature indicator Indicates the temperature setting. A, B change indicator remote controller When the remote controller switching function is set, "B" appears in the remote controller display (When the remote controller seting is "A", there is no indication at this position. ) 6. Operation Indicate when press the operation ON/OFF button. AUTO, QUIET or three fan speed levels ( LOW , MED , HIGH ) can be shown. 4. 7. 8. ON/OFF TIMER indicator Indicate when the ON/OFF TIMER operation. ON], OFF TIMER [OFF]). 5. 2 1 3 6 HEAT B Hr. ON OFF 7 4 8 5 45 FILE NO. Installation Diagram of Indoor and Outdoor Units 65 mm or more 170 mm or m Hook ore 1 Installation plate For the rear left and left piping Wall Hoo k 170 mm or m ore Insert the cushion between the indoor unit and wall, and tilt the indoor unit for better operation. Do not allow the drain hose to get slack. (A tta ch to t he 5 Active carbon catechin fro nt p Shield pipe an el) Cut the piping hole sloped slightly. 6 Active carbon catechin Make sure to run the drain hose sloped downward. 4 Remote control holder Vinyl tape Apply after carrying out a drainage test. 8 Pan head wood screw 2 Wireless remote control The auxiliary piping can be connected to the left, rear left, rear right, right, bottom right or bottom left. 600 mm or more Right Rear right 100 45 m rm mo ore Saddle Bottom right Left Rear left Bottom left mm or mo re ore 400 m rm mo 600 Extension drain hose (Not available, provided by installer) mm or mo re Insulate the refrigerant pipes separately with insulation, not together. 6 mm thick heat resisting polyethylene foam Before installing the wireless remote control With the remote control cover open, load the batteries supplied correctly, observing their polarity. Optional Installation Parts Part Code Parts name Refrigerant piping Indoor unit name Y Q'ty Liquid side (Outer diameter) 6. 35 mm Gas side (Outer diameter) 1 ea. 9. 52 mm RAS-107SKV-E Z Shield pipe (for extension drain hose) (polyethylene foam, 6 mm thick) 1 Attachment bolt arrangement of outdoor unit Secure the outdoor unit with the attachment bolts and nuts if the unit is likely to be exposed to a strong wind. If it is necessary to drain the defrost water, attach drain nipple to the base plate of the outdoor unit before installing it. 500 mm 97 mm 2 Air inlet 280 mm 53 mm 5 Air outlet Drain outlet 10-2-2. Accessory and Installation Parts Part No. Part name (Q'ty) Part No. Part name (Q'ty) Part No. Part name (Q'ty) Installation plate 1 Active carbon catechin x 1 Drain nipple* x 1 Wireless remote control 1 Active carbon catechin x 1 Parts marked with asterisk (*) are packaged with the outdoor unit. <Others> Name Owner's manual Battery 2 Mounting screw 4 25L 6 Installation manual Important information and warning* B/W strips* (Energy efficiency labels) Remote control holder 1 Remote control holder mounting screw 3. 1 16L 2 This model is not equipped with an extension drain hose. 47 FILE NO. Installation/Servicing Tools Changes in the product and components In the case of an air conditioner using R410A, in order to prevent any other refrigerant from being charged accidentally, the service port diameter of the outdoor unit control valve (3 way valve) has been changed. (1/2 UNF 20 threads per inch) In order to increase the pressure resisting strength of the refrigerant piping flare processing diameter and size of opposite side of flare nuts has been changed. (for copper pipes with nominal dimensions 1/2 and 5/8) New tools for R410A New tools for R410A Applicable to R22 model Changes As pressure is high, it is impossible to measure by means of conventional gauge. In order to prevent any other refrigerant from being charged, each port diameter has been changed. In order to increase pressure resisting strength, hose materials and port size have been changed (to 1/2 UNF 20 threads per inch). As pressure is high and gasification speed is fast, it is difficult to read the indicated value by means of charging cylinder, as air bubbles occur. [. . . ] 3) Remove the hooking claws by pushing a minus screwdriver according to the arrow mark in the right figure, and remove the fan guard. Attachment 1) Insert the claws of the fan guard in the hole of the front cabinet. Check that all the hooking claws are fixed to the specified positions. Remarks Fan guard Minus screwdriver Hooking claw 87 FILE NO. Disconnect the leads and connectors connected to the other parts from the control board assembly. [. . . ]