[. . . ] PJ-Net Organizer
PJ-Net Organizer
Preparation Installation Basic Setting and Operation Controlling the Monitor Serial Port Use Appendix
Model No. POA-LN01
This PJ-Net Organizer is an optional product to control and set up a monitor via a network. By accessing the connected monitor using the web browser on your computer, the monitor can be controlled and set up remotely. This product is only used for Monitors that have a terminal for the PJ-Net Organizer. [. . . ] *2 If the network already has the TCP/IP protocol set, enter with the same IP network number for the IP address and Subnet mask. *3 There are some ways to set up the network depending on your computer's appearances.
17
Configure the network of computer
Windows XP
This example explains how to set the following network address.
IP Address : 192. 168. 0. 5 Subnet Mask : 255. 255. 255. 0 Gateway Address : 192. 168. 0. 1
1 Select
2 3
4
5
the Control Panel menu from the [Start] menu. Click the Network and Internet Connection and then click the Network on the control panel. Click the Local Area Connection icon with right button of the mouse and then select the Property menu. Select the General tab on the "Local Area Connection Properties" dialog window. Select the Internet Protocol(TCP/IP)*1 and then press the Properties button. On the "Internet Protocol (TCP/IP) Properties" dialog window, select the Use the following IP address button and then enter the IP address*2 and Subnet mask. the OK button, the setting window will be closed.
6 Click
This setting is not needed if the network does not provide the gateway (router).
*1 Select the "TCP/IP" item of the LAN card you use. If the "TCP/IP" item is not listed in the column, you need to install the TCP/IP protocol. For further information refer to the user's manual of your computer. *2 If the network already has the TCP/IP protocol set, enter with the same IP network number for the IP address and Subnet mask. *3 There are some ways to set up the network depending on your computer's appearances.
18
Installation
Notice about system construction
In case of installing the monitor with PJ-Net Organizer into the network constructed with the DHCP/BOOTP server.
This PJ-Net Organizer does not support the DHCP/BOOTP server. To use this product in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP address configured to this product for another device on the network. Please contact your network administrator for further information.
19
Note
20
2
Basic Setting and Operation
21
Basic Setting and Operation
This chapter describes basic operations and settings for controlling the monitor via a network using this product. It is required that computer and monitor are connected to the network and the network address be properly configured.
Login the setting page of the monitor
1 Enter the IP address
Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and the press the "Enter" key.
Enter the IP address that you configured in chapter "Network Configuration" on page 13. The default IP address is [192. 168. 0. 2].
2 Login
If the setting page has set the password, the authentication window will appear. In this case type "user" onto the User Name text area and the login password onto the Password text area and then click OK button. If you check the item "Remember my password", you can login without entering the password for the next login. * The entering User Name must be "user" and it cannot be changed.
[Note] When accessing the monitor at first time or setting the no password [0000], the autologin will be performed and the next main setting page is displayed.
Important
If you have forgotton current network configuration(IP address, subnet mask, password DNS, and default gateway, you can set them to default value via serial port (RS232C) Refer to page 42
22
Login the setting page of the monitor
3 Display of setting page
The following setting page of the monitor is displayed. The main menu which can be set up and control the monitor appears on the lower side of the page. On the setting page, the control and status items for selected menu are displayed. For further information, please see chapter "Controlling the monitor" on page 31.
Sub Menu
Setting Page
Main menu
23
Basic Setting and Operation
Initial Settings
After installing this product onto the monitor, perform the following basic initial setting. [. . . ] Press the Save button to memorize.
The maximum 127 characters can be typed.
Use other command
This function can be used to send other command which does not have in the menu of this board. Type the command and press the Send button to control the monitor.
Please see the chapter "4: Serial Port Use" on page 39 or the owner's manual of the monitor for other command. ("Configurations of RS232C Terminal") The box of Explanation can be used for the title.
37
Note
38
4
Serial Port Use
39
Serial Port Use
This Network Board provides with a serial control port (RS232C) to control the monitor.
Example of Connection
Control the monitor through network and serial control function.
AV1
Power ON !
RS232C serial cable with reverse type (Not supplied)
Specification and Setting of RS232C Terminal
Terminal : HDB9-PIN Pin Configuration 1 2 3 4 5 No Connect RxD TxD No Connect Ground 6 7 8 9 No Connect No Connect No Connect No Connect
9 8 7 6 5 4 3 2 1
Connection
Interface (Fixed) Protocol Baud rate Data length Parity Stop bit Flow control RS-232C 19200 bps 8 bits 1 bit -
RS232C serial cable with reverse type (Not supplied)
Exclusive driver software for control of this Network board is required. Usually, when connecting between this product and a computer, use Reverse type of serial cable (Serial Cross Cable).
40
Serial Port Use
Command for controlling the monitor
The below commands for controlling the monitor can be used.
PSAVE PSAVE
EXAMPLE : POWER ON (C00)
HEX ASCII FUNCTION CODE / END CODE 43h 30h 30h 0Dh 0Ah 'C' '0' '0' [CR] [LF]
41
Serial Port Use If you forgot current network configuration, (IP address, subnet mask, password DNS, and default gateway), you can set them to default value via the serial port (RS232C).
How to set Network configuration on network board to default
1 Send below command (ASCII) to network board 2 Network board will be rebooted. [. . . ]