[. . . ] Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. Before installation or service, disconnect the power supply to the work area by removing the fuse, "tripping" the circuit breaker, or unplugging the unit.
4
IMPORTANT SAFETY INSTRUCTIONS
This appliance must only be used after it has been installed in cabinetry to ensure all electrical components are shielded. Tampering with electrical connections or components and mechanical parts is dangerous and can cause machine damage. [. . . ] The appliance starts to heat once a duration is set.
9
Guide to the controls
Temperature selector
The temperature is infinitely variable between the basic setting (see illustration) and the "High" setting.
The temperature settings: Basic setting: 97°F (36 °C) Low: 140 °F (60 °C) Medium: 176 °F (80 °C) High: 203 °F (95 °C)
10
Guide to the controls
Humidity control
"Moist": This position closes the vents and seals the moisture in the drawer to keep food moist and soft. "Dry": This position opens the vents for maximum airflow to keep food crisp. This setting is ideal for keeping both dry and liquid foods warm, e. g. In this setting moisture may collect on surfaces above the warming drawer. The humidity control can be set anywhere between "Moist" and "Dry". "Center": This position is between "Moist" and "Dry" and partially opens the vents to keep food warm and slightly moist, e. g. Allow extra time for the temperature to adjust after adding or checking on food or dishes. Please note: Be careful not to place food too close to the upper heating element. Increased temperature and proximity may cause a fire!
14
Using the warming drawer
Keeping food warm
For best results, preheat the warming drawer before warming food. Preheating times: "Low": 6 minutes "Medium": 10 minutes "High": 14 minutes ^ Once the preheating time has elapsed, place the hot food in the warming drawer. Do not add water to food or place a container with water in the warming drawer. Take care when opening and closing the loaded drawer to prevent spills. ^ The warming drawer can be turned off at any time by turning the timer to the "0" setting. When warming is complete keep the drawer open for a few minutes to allow the humidity to evaporate.
15
Using the warming drawer
Warming dishes
The warming drawer can also be used to warm dishes. ^ Turn the temperature selector to: - "Low" if dishes are on the rack or are light weight. - "High" if dishes are on the floor of the drawer or are heavy or thick. Keep in mind that the temperature setting to keep food warm may be higher than the temperature required to warm dishes. When warming food and dishes at the same time, place the dishes on the floor of the drawer and the food on the rack.
16
Warming drawer care
, CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Danger of burns!
Appliance front and control panel
^ All external surfaces and controls can be cleaned with warm water and liquid dish soap applied with a sponge. ^ Wipe dry using a soft cloth.
Glass
Glass surfaces can be cleaned with a glass cleaner.
Stainless steel
Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner.
Avoid the following on all surfaces: - abrasive cleaning agents, e. g. pot scourers or sponges that were used with abrasive cleaning agents, and - oven sprays.
17
Warming drawer care
Drawer
The drawer can be removed for easier cleaning. Removing the drawer
Non-slip mat
^ Clean the non-slip mat by hand with warm water and liquid dish soap. [. . . ] Installation in combination with an oven: A minimum gap of 1" (2. 5 cm) must be present between the upper edge of the warming drawer and the oven. This gap should be sealed with a moisture resistant sealing material.
26
Installation
Dimensions for Solo Installation ESW 47x0
a Material must be moisture resistant
27
Installation
ESW 48x0
a
24" ) 0 (61 " 1/2 28 ) "- -724 26 60 (6
(280)
101/8" (257)
(51)
2"
) 25(659
15
(248)
9 3/4"
22 1 5/ 16 (5 82 " )
1" (2 6)
29 57) (7
13
/1
6"
a Material must be moisture resistant
28
11"
/16
"
Installation
Dimensions for a combination installation with an oven ESW 47x0
a Material must be moisture resistant
23 7/16" (596)
22 13/16" (580)
1/8"
(2, 8)
a
(25)
111/16" 10 1/8" (257)
1"
11" (280)
11/16"
3/16"
(5)
3/8" (10)
(18)
(43)
29
Installation
ESW 48x0
a Material must be moisture resistant
30
Installation
Installing the warming drawer
^ Remove the drawer from the casing before installing the appliance into the cabinetry. Removing the drawer ^ Push the casing in the cabinetry.
^ Secure the casing in the cabinetry with the six screws. Inserting the drawer ^ Pull the drawer completely out and loosen the nuts. [. . . ]