[. . . ] Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChec ende less tion. comm un ra re er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChec ende less tion. comm un ra re er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. [. . . ] Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChecmende less n. m un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChecmende less n. m un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subjked crac
CHUTE LATCH
GRASS CATCHER CONTAINERS LOWER CHUTE LOWER CHUTE ATTACHING STRAPS
NOTE: When right hand (R. H. ) and left hand (L. H. ) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position.
THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER:
(1) 3/8" Wrench (1) 1/2" Wrench (2) 9/16" Wrenches (1) 1/2" Socket (1) 9/16" Deep well Socket
(1) Drive Ratchet (1) 3" or longer Extension (1) Short Handle Phillips Screwdriver
CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: · Depress clutch/brake pedal fully and set parking brake. Assemble support post to container support with the three (3) carriage bolts and locknuts. 1C) · Assemble the mounting bracket, lanced tabs towards bottom, using the four smaller inside holes on the drawbar. · Install the four bolts and locknuts as shown and tighten securely.
SUPPORT POST LOCKNUTS
7
FIG. 4) Use Hardware - - GROUP "C"
5
· · · ·
CONTAINER ASSEMBLY (See Fig. 5) No hardware required
NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting assembly to tractor. · With cover closed, lift assembly and place support post inside mounting bracket. · Line up holes in mounting bracket with holes in support post and insert bracket support pin. · Install the three (3) tubing end caps onto container support. · Tap each end cap onto container support tubes to seat securely.
BRACKET SUPPORT PIN COVER ASSEMBLY
Place bottom half inside of top half, as shown. Place one foot inside bottom half and lift top half to meet bottom half. Press halves tightly together while lifting top to lock into place as shown.
IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET.
Repeat for second container.
CONTAINER BOTTOM HALF
CONTAINER TOP HALF CONTAINER BOTTOM HALF RETAINER SPRING
PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF LOCKING TAB
ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above.
END CAP
r is ne tai en . Con wh r. Re conta erlyientlyment prop qu ce r is g fre pla ine ba d re nta eck de s co Ch en les tion. comm r un ra re we tierio ly a mo de on RNerate and Use WA t op wear ged. no to ma Do ct da bje or su cked cra
ING
SUPPORT POST
LANCED TABS
FIG. 6) No hardware required
Install one container to left side first with warning to outside of unit. NOTE: Right container should always overlap left container at center support. [. . . ] · Disengage blades and stop engine before leaving tractor seat to empty containers, unclogging chutes, etc. · Disengage mower when crossing driveways or gravel surfaces and other areas where thrown objects could be a hazard. · Do not attempt to vacuum up cans or other potentially hazardous projectiles.
·
·
11
CUSTOMER RESPONSIBILITIES
GENERAL RECOMMENDATIONS
Always observe safety rules when performing any maintenance. · Clean unit thoroughly after each use.
STORAGE
When grass catcher is to be stored for a period of time, clean it thoroughly, remove all dirt, grass, leaves, etc. [. . . ]