[. . . ] 41-68 LAMP REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69-72 CARE OF YOUR HITACHI TV & REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 RECEPTION PROBLEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 USEFUL INFORMATION / INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To switch to DVD pre-coded mode, use the SOURCE ACCESS buttons ( the corresponding selection. , ) on the remote control to position the LED light to 4. Hold down the ENT button on the remote and enter the four digit preset code that matches your DVD player, as shown on pages 39-40. The remote will turn off your DVD player when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your DVD player. If the DVD player does not turn off, try a different four digit preset code. 7. THE REMOTE CONTROL You will need to set the display type of your DVD player to 16:9 widescreen. NOTES: 1. If your DVD player cannot be operated after performing the above procedures, your DVD player's code has not been precoded into the remote. In the unlikely event that your DVD player cannot be operated after performing the above procedures, please consult your DVD player operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. GUIDE PRECODED DVD Buttons These buttons transmit the chosen precoded DVD codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. C. C. MY DVD PLAYER CODE IS: NOTE: Refer to instruction manual of the DVD player for operation of the buttons exclusively for the DVD player. 35 USING YOUR REMOTE TO CONTROL VCR/PVR FUNCTIONS Operating the precoded function for your VCR/PVR (Personal Video Recorder). In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide. The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP). INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices. PRECODED AUDIO Buttons These buttons transmit the chosen precoded Audio component codes. EXCLUSIVE TV Buttons These buttons are for operating the TV. GUIDE C. C. MY AUDIO EQUIPMENT CODE IS: CD AMP/RCVR NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes. Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment. 37 USING YOUR REMOTE "ENT" BUTTON TO ACCESS THE SPECIFIED INPUT OF THE TV INPUT ACCESS This optional feature allows the user of the remote control to setup it's ENTER (ENT) button to access the specified input of the TV. Setup for this feature is applicable to the remote control's normal mode only and only applies to the DVD, CBL, STB, PVR and AMP modes. Select the desired device mode (DVD, CBL, STB, PVR, or AMP) by using your SOURCE ACCESS buttons ( , LED indicator to the corresponding selection. [. . . ] Subject to all of the terms, conditions and restrictions of this License Agreement, HAL-HED grants to you a limited, revocable, non-exclusive right to use one copy of the Software only on one Hitachi labeled DTV owned by you. You may not resell or otherwise transfer for value the Software, except that you may transfer the Software as part of a resale of the entire DTV product only. Prohibition on Reverse Engineering, Decompilation, Disassembly and/or Modification. You may not reverse engineer, decompile, disassemble or modify the Software. [. . . ]