[. . . ] Refrigerator
user manual
This manual is made with 100% recycled paper.
English
imagine the possibilities
Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at
www. samsung. com/register
Free Standing Appliance
safety information
safETy inforMaTion
WarninG
see which refrigerant is used for the refrigerator. · In case of R600a refrigerant, this gas is natural gas with high environmental compatibility that is, however, also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. [. . . ] Under normal conditions, a 170 cc paper cup can be filled in 10 seconds. If the refrigerator is installed in an area with low water pressure (below 138 Kpa), you can install a booster pump to compensate for the low pressure. Make sure the water storage tank inside the refrigerator is properly filled. To do this, press the water dispenser lever until the water runs from the water outlet. After connecting the water supply to the water filter, turn your main water supply back on and dispense about 1l to clear and prime the water filter.
Close Main Water pipe
01 sETTinG UP
Close Main Water pipe
no gap
Connectingthewaterlinetothe refrigerator
1. Remove the dust cap from the water line on the rear of the unit and fit a compression nut from the install kit. Remove the water pipe from the install kit and fit a compression nut to one end. Join the two pipes together using the compression joint from the install kit ensuring that the joint is water tight. Join the other end of the install pipe to the main water supply and turn on the water to check for leaks.
insTaLLinG THE WaTEr DisPEnsEr LinE
ForInteriormodel PartsforwaterlineInstallation
1 Water line fixer and
2 Pipe connector
screws Loosen a
remove cap
Water Line from unit
3 Water line 4 Water filter
no gap
Connectingtothewatersupplyline
1. Follow the water line installation instructions in the installation kit. If it is connected to the hot water pipe, it may cause the purifier to malfunction.
CaUTion
Water Line from Kit
Only connect the water line to a drinkable water source. If you have to repair or disassemble the water line, cut off 6. 5mm of the plastic tubing to make sure you get a snug, leak-free connection. Before being used, the leakage in these places should be examined
setting up _11
· Samsung Warranty does not cover WATER LINE INSTALLATION. · The cost of connection to a water supply is at the customer expense, unless included in the delivery charge (refer to the delivery agreement with the seller) · Please contact Plumber or Authorised Installer for the installation if needed. · If Water leakage occurs due to improper installation, Please contact installer.
insTaLLinG THE WaTEr DisPEnsEr LinE
ForExteriormodel PartsforwaterlineInstallation
Pipe connector Water line fixer and screws
Water line
Purifier lock-clip
Purifier
Connectingtothewatersupplyline
Connect the water pipe with coupler and tap. If it is connected to the hot water pipe, it may cause the purifier to malfunction.
WARRANTYINFORMATION
This water line installation is not covered by the refrigerator or ice maker manufacturer's warranty. Follow these instructions carefully to minimise the risk of expensive water damage.
Note:
If the coupler does not fit on the current tap, go the nearest authorised service dealer and purchase the right couplers fittings.
Selectthelocationwherethepurifier istoinstall. (Modelwiththepurifier)
- If you wish to reassemble the water inlet and outlet sides of the purifier during purifier installation, see the reference illustration. - Cut the water line attached to the purifier to the appropriate place after measuring the distance between the purifier and the cold water tap.
12_ setting up
CoUPLEr "a"
Removeanyresidualmatterinside thepurifier. (Modelwiththepurifier)
- Open the main water tap to check whether water is running through the water tube on the water inlet side of the purifier. - If water does not come out through the line, check whether the tap is open. - Leave the tap open until clean water is running out and any residual matter that built up during manufacturing has been removed.
oUTLET siDE of PUrifiEr PUrifiEr
TaP LinE oUTLET
01 sETTinG UP
siDE of PUrifiEr PUrifiEr WaTEr
90 degree CaUTion
insert Locking Clip after tube seated
WaTEr WaTEr inLET siDE of PUrifiEr CoUPLEr Locking Clip
WaTEr LinE
ReplacementInstructions
1. Insert water supply tube into the inlet side of the filter until the tube stop.
fLoW DirECTion
Attachthepurifierlock-clip.
- Hold the purifier lock-clip in the appropriate position (under the sink for example) and fix it tightly into place where to screw.
WaTEr sUPPLy inLET siDE
PErMEaT Purifier lock-clip
Note: You must also ensure that the cut is square and not at any sort of angle as this could cause a leak
4. The Clip fix the tube.
Securethepurifierinposition.
- Fix the purifier in position, as shown in the figure on the right.
WaTEr TUBE PUrifiEr LoCK-CLiP
5. [. . . ] Is the temperature control on the display panel set to the correct temperature?Is the refrigerator in direct sunlight or located too near a heat source?Is the back of the refrigerator too close to the wall and therefore keeping air from circulating?Is the temperature control on the display panel set to the correct temperature? [. . . ]