[. . . ] If you want to create RAID, assure that the Onboard H/W GIGARAID item under Integrated Peripherals is set to Enabled and GigaRAID Function to RAID (Figure 1). If you do not want to create RAID, set GigaRAID Function to ATA.
CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals
: Move Enter: Select F5: Previous Values
+/-/PU/PD: Value F6: Fail-Safe Defaults
F10: Save
ESC: Exit F1: General Help F7: Optimized Defaults
Figure 1 The BIOS Setup menus described in this section may not show the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version .
-3-
IDE RAID Drives Configuration (GigaRAID)
Ác Åé ¤¤ ¤å
Step 2 Next, go to Advanced BIOS Features and select Hard Disk Boot Priority. In the Hard Disk Boot Priority submenu, use the ARROW keys to select the desired IDE hard drive onto which you want to install Microsoft Windows 2000/XP and use the PLUS SIGN to move it up to the first item. [. . . ] IDE RAID Drives Configuration (GigaRAID) -4-
(3) Configuring RAID set in RAID BIOS
Enter the RAID setup utility to create RAID set on the GigaRAID controller. Skip this step and proceed to Section 4 if you do not want to create RAID. Step 1: If you have attached hard drives to the GigaRAID controller correctly, after the Power-On Self Test (POST) memory test begins and before the operating system boot begins, the GigaRAID BIOS will detect the drives attached and show the following screen.
Figure 4 After entering the GigaRAID Setup Utility, you should see a screen similar to Figure 5 below. Navigate the GigaRAID Setup Utility: You can use Number keys 1 to 5 to select the item you need. Auto Configuration [1]: It will guide you to set an array and this is the simplest and fastest way to create your first array. Define RAID [2]: To manually create an array, press 2 to enter the Define RAID menu. Delete RAID [3]: To delete existing RAID set, press 3 to enter the Delete RAID menu. Rebuild RAID [4]: To rebuild RAID 1 or RAID 0+1 set, press 4 to enter the Rebuild RAID menu. RAID Card Configuration [5]: To check information about the RAID controller and current hard drive status, press 5 to enter the RAID Card Configuration screen.
Figure 5
-5-
IDE RAID Drives Configuration (GigaRAID)
Ác Åé ¤¤ ¤å
Auto Configuration Auto Configuration will guide you to set an array and this is the simplest and fastest way to create your first array. You should see a screen similar to Figure 6 below after pressing 1 from the Main Menu. Auto Configuration Menu: You can use the ARROW keys or SPACEBAR to cycle through RAID mode options under the Setup Array Type as item. Later, answer Y or N to the next prompt "Do you like monitoring the reconstruction status till it completes?" If you answer Y, you can monitor the whole rebuild process until it completely ends or select background rebuild. If you choose background rebuild, rebuild can proceed at the background and you can leave Setup Utility and boot directly.
Figure 14
IDE RAID Drives Configuration (GigaRAID)
- 12 -
RAID Card Configuration: Press 5 in Main Menu to enter the RAID Card Configuration menu (Figure 15). The RAID Card Configuration section: When Auto-Rebuild is enabled, the GigaRAID ATA RAID Controller can rebuild your mirrored array automatically. If a failed mirrored drive is replaced without shutting down your PC, the GigaRAID ATA RAID Controller can detect the hot-swap action and start rebuilding automatically. When Auto-Rebuild is disabled, you need to rebuild your mirrored array manually from Rebuild RAID Menu (please refer to page 11). The RAID Card Resource section: This section displays PCI slot interrupt and I/O port address used by the GigaRAID ATA RAID Controller. The Driver Status section: This section displays the status of each hard drive.
Figure 15
- 13 -
IDE RAID Drives Configuration (GigaRAID)
Ác Åé ¤¤ ¤å
(4) Making a IDE RAID controller driver disk
To install Windows 2000/XP onto a hard drive on the GigaRAID controller successfully, you need to install required driver for the GigaRAID controller on your motherboard during OS installation. Without the driver, the hard drive may not be recognized during the Windows setup process. First of all, you need to copy the driver for the IDE RAID controller from the motherboard driver CD to a floppydisk. Step 1: Find an available system and insert the motherboard driver CD into the CD-ROM drive. Step 2: Go to My Computer and right-click the CD-ROM drive icon and select Open (Figure 11).
Figure 16
Step 3: Go to the BootDrv folder and look for an executable program named MENU. exe (Figure 17).
Figure 17
IDE RAID Drives Configuration (GigaRAID)
- 14 -
Step 3: Double-click MENU. exe. [. . . ] Step 2: Go to My Computer and right-click the CD-ROM drive icon and select Open (Figure 11).
Figure 16
Step 3: Go to the BootDrv folder and look for an executable program named MENU. exe (Figure 17).
Figure 17
IDE RAID Drives Configuration (GigaRAID)
- 14 -
Step 3: Double-click MENU. exe. An MS-DOS prompt screen similar to Figure 18 below will appear.
Figure 18
Step 4: Insert an empty floppy disk. Then it will take about one minute to copy the GigaRAID driver from the motherboard driver CD to the floppy disk. You have copied the IDE RAID driver sucessfully.
Figure 19
- 15 -
IDE RAID Drives Configuration (GigaRAID)
Ác Åé ¤¤ ¤å
(5) Installing IDE RAID controller driver during OS installation
Now that you have prepared a floppy disk with the IDE RAID controller driver and adjusted BIOS settings, you are ready to install Windows 2000/XP onto your IDE hard drive with the driver. [. . . ]