[. . . ] © All right reserved to netafim / Hendelmade 0901 The smart valve with 3 Independent programs + 2 extra modes & AD l en f o opciona RE ario programad EP KE AQUA PRO Irrigation Controller E Easy to use battery operated irrigation controller. Two in one: an irrigation controller and AQUANET, a state of the art electric valve combined. [. . . ] -U nce da s & n: ba w p to da ily a & Irri ttery 3 ir ily o t sa du ga rig n se me ra tio ati le tim tio n on cte e sta sp d . 1, e > ET <S E> OD <M Table of contents: Installation Controller Keyboard Controller Icons & Display Electric valve control button Battery Insertion or replacement Installation into the watering system Programming steps Set P1 Set p2 Set P3 Programming guide table Controller display in operating mode Technical information Warranty > ET <S E E> OD <M E> OD <M E> OD <M > ET > <S SET < > ET > <S SET < tiv 3, 5 eD , 7 ay , s. . 4 5 6 7 8 9 10 11 12 14 15 3 E Installation Controller Keyboard <MODE>: To select operating sequence and to enter programming. Low battery. 4 Electric valve control buttons Auto: Close: Open: Note: If the override button (marked with a red arrow) is in Close position the AQUA PRO will remain closed. If the override button (marked with a red arrow) is in Open position the AQUA PRO will remain open. Flow Control: Flow Direction: (see page 7) E 5 Battery Insertion or replacement E Note: to operate your controller you need a high quality 9V alkaline battery (not included) The Low battery sign appears - insert or replace the battery To insert or to replace the battery: 1. Install the AQUA PRO into the watering system making sure that the water flow is in the direction of the arrow on the base of the valve. You can control the flow using the Flow Control lever on the base marked from <+> to <->. E When installing the AQUA PRO, hold the valve only. 7 E Programming steps Note: Make sure that the override button (marked with a red arrow) is in the central position AUTO). If no key is pressed for more than 30 seconds during programming, the controller resumes operating mode. 8 Set P1 Once a day at the same time every day. P1 programming is completed. E 9 E Set P2 Once a day at the same time on selected Active days Note: Irrigation duration and start time has already been set at P1. To change irrigation duration and/or start time, go back to P1 (7-14) Press <MODE> three times for 2 seconds. day 1 ÒblinksÓ 10 Set P3 Up to three start times per day on selected Active days. Note: To select an active program: press the <MODE> button briefly: once for P1, twice for P2 three times for P3. and four times to turn the controller OFF. E 11 E Programming guide table (example) Example Day Active day Duration Start time 1 x 0:15 08:00 P1 2 3 4 5 6 7 x x x x x x Example Day Active day Duration Start time 1 x 0:15 08:00 P2 2 3 4 5 6 7 x x x Example Day Active day Duration Start time 1 x 0:15 1 P3 2 3 4 5 6 7 x x x 0:15 0:15 2 3 Hour 08:00 13:00 18:00 12 Your program guide table P1 Day Active day Duration Start time 1 2 3 4 5 6 7 x x x x x x x E P2 Day Active day Duration Start time 1 2 3 4 5 6 7 P3 Day Active day Duration Start time 1 2 3 4 5 6 7 Hour 13 E Controller display in operating mode Real time clock Current day (blinking) Active mode (P1, P2, P3 or OFF). Technical information Flow Range: 25-6000L/H (0. 1 to 26 GPM). Maximum extension from the valve to the Controller 100 M (330- feet) (cable 1. 0mm Ø). AQUA PRO controller is compatible also with Aquanet 1. 5", 2". [. . . ] This manufacturer warranty policy may apply differently in different countries. For more information, contact your Netafim distributor Email: postmaster@Netafim. com E 15 [. . . ]