[. . . ] OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating your set and retain it for future reference.
MODEL L330-DN L330-DP L330 Series
P/NO : MFL67260109
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. [. . . ] A qualified service person, complying with all applicable codes, should perform all required hardware installation. Do not expose the power and connection cable to moisture, which may cause damage to the unit.
Connection Overview
10
Connections
Connecting Display device
The video signal connection between the camera and the monitor.
Connecting Power Source
Connect power, using the method listed below: 1. (b) Connect to the DC 12 V UL Listed, Class 2 Power Supply only on the unit.
11
Connections
Mounting the Lens
1. era opening and turn the lens slowly to install it.
2-2
2-1
2.
Install the auto-iris lens. CS mount type lens Carefully align the lens mount with the camera opening, then turn the lens slowly to install it. C mount type lens To allow for flange- back adjustment, install the C-mount adaptor (option) on the lens mount, then carefully align the lens mount with the cam3. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect a lens iris plug according to the diagram. (Refer to next page. )
2-2
2-1
12
Connections
lens iris output connector
Pin layout for the lens iris output connector.
Rewire the lens iris plug
1. Cut off the plug of the lens cable, cut off approximately 8 mm of the insulation, and then strip approximately 2 mm of the ends of the cable sheaths.
No. Solder the ends of the cable wires to the ends of the pins, and then attach the cover of the lens iris plug.
13
Connections
Flange-back Adjustment
The adjustment is required only when a lens without focus-adjusting mechanism is mounted, or when a lens with adjusting mechanism is mounted and focus that is more accurate is needed. Note: The object may be out of focus when using a source of near-infrared light than using the visible light.
2.
Use the flange-back adjusting ring to obtain a focused point while watching the monitor screen.
14
Connections
Mounting the camera
The mounting bracket can be secured on either the top or bottom of the camera. Use the same set of screws to attach the mounting bracket on the camera. Note: If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely.
15
Menu Operation
OSD Menu control buttons
This camera utilizes an on-screen user MENU. The setup menu screen appears.
LENS Setting
Select the desired lens iris value for camera exposure. Select AUTO or MANUAL mode from [LENS] menu, and select a value.
2. 5.
Use [UP] or [DOWN] button to select an option then press [SET] button. In the submenu, use [UP] or [DOWN] button to select the [RETURN] then press [SET] to return to the previous setup menu. MANUAL: You can set the electronic shutter value and AGC value by adjust manual exposure. [. . . ] It is order to reproducing brightness properly and brightness differences.
1. 2.
Select [ATR] option and use [LEFT] or [RIGHT] button to select ON or OFF. CONTRAST: You can select the Contrast limit.
27
Menu Operation
NR Setting
If you select high value, you can reduce the more noise. When you use this function, the afterimage may occur.
Motion Detection Setting
The motion detection detects the moving objects in the scene by monitoring changes in brightness level.
1. [. . . ]