[. . . ] * Make sure the connectors on the cables connected to the display do not press against the wall.
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Follow all instructions.
Warning
This wall mount should be installed by a trained and experienced installer designated by the retailer.
Having the product installed by a non-specialized installer is very dangerous and can cause damage or injury.
Do not install the product where the weight cannot be supported.
If the strength of the location where the wall mount is installed is not strong enough, it can fall off and cause an injury.
Use a trained and experienced installer to move or replace the wall mount, if needed.
Installation requires special techniques and moving or installing the product on your own can cause serious safety issues.
After installing the wall mount, do not hang on the product or apply severe impact to the product.
The product can fall off and cause injury.
When installing the wall mount, never hang the power or signal cable on the rear side the TV.
The cord can be damaged and cause a fire, an electric shock or damage to the product. [. . . ] 3.
2
Attaching the mounting bracket on the TV
Make sure the screws are fully tightened to the bracket and display. If the screws will not fully tightened, they might be too long or the wrong size.
VESA 100X100 / VESA 200X100 is supported. If needed, you may refer to the display's user manual to verify the display has one of the supported VESA formats.
Screws are included for the following models: M4 X 10mm : 19/22LD*, 19/22LE*, 19/22LX*, 19/22LK*, 19/22LZ*, 19/22LW*, 19/22LV*, 26LE65* M4 X 14mm : 26/32LD*, 26/32LE*(Excludes 26LE65*), 26/32LX*, 26/32LK*, 26/32LZ*, 26/32LW*, 26/32LV*
Bracket to attach to the display
VESA 200 VESA 100
VESA 100
Install the PVC washer between the brackets and the display on the following models : 32LE53*/32LE55* But for 26LE53*/26LE55* model, this is provided as TV component.
<Work procedure> 1. Check to see if the display has screws already installed into the VESA mounting holes. - Make sure the screws are fully tightened to the bracket and display.
4
- Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack.
Please follow the below direction.
- Check the material of the wall and the thickness of the finishing. - When installing the product on wall material not designated, install the product so that each fixated location can withstand the pull out load of 70kgf (686N) and shear load of 10kgf (980N) or above. Anchor
a b c
Wall mount screw
d e
- Use the Ø8mm drill bit for concrete and hammer (Impact) drill. Use a drill bit Ø8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm. Set the wall mount on the wall by aligning to the location of the hole. Then, fasten the bolts at torque of 45 - 60 kgf/cm.
4
How to install the wall mount <When installing on a masonry wall>
When
you separate the 4 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier to install the product.
A
Wall mount screw
Separate the wall mount screw.
When installing the product on a masonry wall, turn the 4
screws on the A part counterclockwise to separate the screw and bracket. After aligning the wall bracket to the location to install, mark the part to screw on the wall and then remove the wall bracket. Use a level to check whether the wall mount is level.
f the screw cannot be assembled in the designated location inevitably, it can be assembled by rearranging to the closest location. [. . . ] <With the bracket removed. >
Model Name Width (mm) Height (mm) Depth (mm) Weight (kg) Wall Mount VESA Specification Max. UL Load Capacity (kg) LSW100B/LSW100BG 221 152 14 0. 9 100 X 100/200 X 100 15
Min.
LSW100B/LSW100BG 435 167 20 1. 7 100 X 100/200 X 100 15 7
20
<With the bracket attached. >
Model Name Width (mm) Height (mm) Depth (mm) Weight (kg) Wall Mount VESA Specification Max. [. . . ]