[. . . ] Operating Instructions
Inspira Series G 2120 G 2140
To prevent accidents and machine damage read these instructions before installation or use.
en - US, CA
M. -Nr. 51
3
IMPORTANT SAFETY INSTRUCTIONS WARNING
When using your dishwasher, follow basic precautions, including the following: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage.
Electrical Safety
Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. Before installation or service, disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. Do not use an extension cord to connect this appliance to electricity. [. . . ] The indicators "Start/Stop", "Rinse" and the last selected program light. Otherwise important program steps could be interrupted.
Selecting a program
Choose your program according to the type of load and soiling. The "Program guide" describes the programs and use.
Program sequence display
After a program has been started the current stage of the program is indicated by the program cycle indicator.
25
Program guide
Program
When to use
Prerinse 1 2
Program sequence
Main wash Interim rinse 1 2 Final rinse Drying
Pots & Pans
For normally soiled pots and pans with dried on food, also for heavily soiled dishware, use 120% of normal detergent dose Run-time 125 min For normally soiled dishware Run-time 129 min For normally soiled dishware, energy saving program with a long soaking time and a low temperature Run-time 95 min Extended wash time, for sanitizing normally soiled dishware with dried on food Run-time 115 min "Quick program" for lightly soiled dishware, e. g. party dishware includes sensor controlled Glasscare, not suitable for detergent tabs Run-time 30 min To rinse dishes when a complete program is not needed detergent is not recommended Run-time 13 min
x
x
x
x
x
Normal Economy
x
x
x x
x x
x x
x x
SaniWash
x
x
x
x
x
Short
x
x
x
Rinse & Hold
x
Usage: Electric: 0. 01 - 1. 23 kWh Water: 1. 3 - 6. 3 gal (5 - 24 l)
26
Use
At the end of a program
When the program has finished the "End" indicator lights. The dishwasher continues to use electricity until turned off with the s button. vacationing, turn off the water supply.
Interrupting a program
A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted.
, Open the door with care. Close the door firmly until it clicks into place.
Changing a program
If the detergent flap is already open do not change the program. If a program has already started and you wish to change it: ^ Press the "Start/Stop" button for at least one second. ^ Select and start the desired program.
27
Additional functions
Factory default
All settings can be reset to the factory default. ^ Press the "Start/Stop" button and at the same time turn the dishwasher on s. Hold the "Start/Stop" button until the "Start/Stop" indicator comes on. The bottom program indicator flashes once long and twice short in intervals. The "Rinse" indicator flashes: All settings are the factory default. The "Rinse" indicator is off: At least one setting was changed. ^ To reset the dishwasher to the default settings, press the "Start/Stop" button. ^ Turn the dishwasher off s.
28
Frequently asked questions
With the aid of the following guide, minor problems can be fixed without a service call.
, Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage.
Technical faults
Issue The Start/Stop indicator does not flash after the dishwasher is turned on with s. The program cycle indicators "Rinse", "Drying" and "End" flash at the same time. Make sure it is a 15 A breaker.
The fuse has tripped.
The drain pump is running when the door is open.
There may be a technical Turn the dishwasher off fault. Call Miele Technical Service.
29
Frequently asked questions
Problems water intake/drain
Issue The "Intake/Drain" indicator flashes and lights alternately. Solution Open the water supply all the way.
Before fixing the fault: Turn the dishwasher off s. [. . . ] Before discarding an old appliance, unplug it from the outlet, cut off its power cord and remove any doors to prevent hazards.
48
Electrical connection , Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work.
Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current. [. . . ]