[. . . ] e Information button K For displaying additional information about the option selected.
f On button g with indicator light For switching the dishwasher on. h PC interface Used by service technicians to run diagnostic checks, or to update programming data in the future. i In-operation indicator light Shows a programme is running when the door is shut. j Miele{home The appliance is compatible with the Miele|home system.
This instruction book applies to several different dishwasher models. [. . . ] Only open the door if absolutely necessary and exercise extreme caution when doing so. Then close the door firmly making sure that it clicks into place.
38
Operation
Changing a programme
Important: If the detergent dispenser flap has already opened, do not change the programme. If a programme has already started and you wish to change it, proceed as follows: ^ Open the door.
Sensor wash Main wash 1:32h 12:00 Cancel }
^ Select the Cancel function and confirm with OK. The programme will be cancelled.
Sensor wash Programme finished 12:00 Main menu }
^ Select the Main
menu
option.
The display will change back to the main menu. The programme starts.
39
Operation
Additional functions
Delay start The start time of a programme can be delayed, e. g. A delay start time of between 15 minutes and 24 hours can be selected. The delay start time is set in 15 minute steps.
, When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. If the compartment is wet, powder detergent can become lumpy and stick to the dispenser, with the result that it is not fully dispensed. Do not use liquid detergent when selecting Delay start, as it can run into the dishwasher before it is required. , To prevent children coming into contact with dishwasher detergent do not fill the detergent dispenser until just before starting the programme, i. e. The current time of day and the last start time selected will appear in the display. ^ To help prevent re-soiling, a proprietary conditioning agent for stainless steel, such as Neoblank (available from the Miele UK Spare Parts Department) can also be used. Follow the manufacturer's instructions on the label and apply sparingly with an even pressure following the direction of the grain.
43
Cleaning and care
Checking the filters in the wash cabinet
The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms.
Cleaning the filters
^ Switch the dishwasher off.
, The dishwasher must not be used without all the filters in place.
Collection of coarse soil may cause the filters to clog. The level of soiling and time it takes before the filters need cleaning will vary depending on use. The message Check filters will appear in the display after every 40 programme cycles (factory default setting). You can set the interval for this message to appear to between 30 and 60 programme cycles (see "Settings menu J, Check filters"). Remove any coarse particles and rinse the filter well under running water. Use a nylon brush if necessary.
44
Cleaning and care
To clean the inside of the filter, the flap must be opened: ^ Press together the catches a in the direction of the arrows as shown, and open the filter b. ^ Then close the flap so that the catch engages.
^ Replace the filter combination so that it lies flat in the base of the wash cabinet. ^ Then turn the handle clockwise to lock the filter combination in place.
, Take care when you are fitting
the filter combination that it is secured in position correctly. Otherwise coarse soil could get into the circulation system and cause a blockage.
45
Cleaning and care
Cleaning the spray arms
Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. [. . . ] ^ Select the option you want and confirm this with OK.
75
Settings menu J
Setting the buzzer volume You can select one of two options or deactivate the buzzer.
Off:
Keypad tone
An audible tone sounds each time a button is pressed. ^ Select the option you want and confirm this with OK.
The buzzer at the end of a programme is deactivated.
Normal:
The buzzer sounds at a "normal" volume.
Loud:
Brightness
There are seventeen different display brightness settings. ^ Select the setting you want and confirm this with OK.
The buzzer sounds louder. ^ Confirm with OK.
Memory
You can use the Memory function to save the last programme selected. [. . . ]