[. . . ]     K 5HVHW  VHF % K PLQ $ K 6WDUW & 5HVHW VHF                    en Table of contents Hygiene . 16 16 16 16 16 16 16 16 17 17 17 17 17 17 18 18 18 18 18 19 19 20 20 21 21 21 22 22 23 23 23 24 24 24 24 24 25 25 25 26 26 26 26 26 Safety instructions . 16 en Safety instructions Before you switch ON the appliance Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance. [. . . ] The expected programme duration flashes on the digital display )". The programme starts running. Ï Intensive zone * vsIniezot ne Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display )". The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). ¿ Extra drying * nxEtradigy An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption. 16 en nargoTiep m Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Press button @ + until the digital display )" jumps to : . – Press @ + or – button until the displayed time corresponds with your requirements. – To delete timer programming, press the @ + or – button until )" : is indicated on the digital display. You can change your programme selection at any time until the programme starts. To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of : has been reached, the display jumps back to : (off). The set value is saved. Switching off the appliance Short time after the end of the programme: – Switch off ON/OFF switch (. – Remove the utensils when they have cooled down. ã=Warning End of programme The programme has ended when the value : is indicated on the numerical display )". At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Switching off automatically after the end of the programme * myftelargeodfthnpar tncmta lfaSihgouw Interrupting the programme – Switch off ON/OFF switch (. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. nrem Tiatghpo * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). : : : – – – – Appliance does not switch off automatically Off after 1 min Off after 120 min Close the door. The LED for button # flashes and the digital display )" displays the factory setting : . Press programme button # until the factory set value : is indicated on the digital display )". Terminating the programme (Reset) – Press START button P for approx. – Switch off ON/OFF switch (. – 17 en Changing the programme When the START button P has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. [. . . ] The hot water setting : allows you to adjust your appliance optimally to operation with hot water. It is recommended to have a water temperature (temperature of the incoming water) of at least 40 °C and no more than 60 °C. It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler. – Hold down programme button # and press START button P until : . . . [. . . ]