[. . . ]
$%&
5HVHW VHF
3URJUDP (QG
5HVHW VHF
6WDUW
en
Table of contents
Intensive zone . 16 16 16 16 16 16 16 16 17 17 17 17 18 18 18 18 18 18 19 19 20 20 21 21 21 22 23 23 23 24 24 24 24 24 25 25 25 25 26 26 26
Safety instructions . 16
en Safety instructions
Before you switch ON the appliance
Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance. [. . . ] If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling.
The temperature is increased during the cleaning process. chopping boards and baby bottles.
fodH al
Switching on the appliance
– Turn on the tap fully. This programme remains selected unless another programme is selected with the button < H or button > P. The programme starts running.
§ Half load *
If you have only a few items to wash (e. g. It is recommended to put a little less detergent in the detergent dispenser than for a full load.
¿ Extra drying *
nxEtradigy
An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption.
16
en
nargoTiep m
Timer programming *
* depending on model You can delay the start of the programme by 3, 6 or 9 hours. – Keep pressing the Preselected starting time button 0 until the appropriate display 3h, 6h or 9h is lit. – To delete the preselected starting time, keep pressing the Preselected starting time button 0 until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts.
To change the setting, – Press the button < H until the required setting has been selected. Note To save energy, the dishwasher automatically switches off after 2 minutes after the end of the programme.
Switching off the appliance
Short time after the end of the programme: – Open the door. – Remove the utensils when they have cooled down.
End of programme
The programme has ended when the End display ` is lit. – Hold down button > P and press START button h until the End display ` and salt refill indicator )* flash. – Keep pressing button > P until the salt refill indicator )* and rinse aid refill indicator )" flash. The refill indicators )* and )" flash and the displays # and + are lit (= Setting 2). The set buzzer volume can be heard.
ã=Warning
At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops.
Interrupting the programme
– Open the door. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. – Close the door.
17
en
nmgrm Tiatgheproam e
Terminating the programme (Reset)
– Open the door. [. . . ] These will disappear after the first wash cycle.
Technical specifications
Weight: max. 60 kg Voltage: 220–240 V, 50 Hz or 60 Hz Connected load: 2. 0–2. 4 kW Fuse: 10/16 A (UK 13A) Water pressure: at least 0. 05 MPa (0. 5 bar), maximum 1 MPa (10 bar). Inlet rate: minimum 10 litres/minute Water temperature: cold water; hot water max. temperature 60 °C.
Fresh water connection
– Connect the fresh-water connection to the tap according to the installation instructions with the enclosed parts. [. . . ]