[. . . ] The software described herein is governed by the terms of a separate user license agreement. Sony, DVgate, i. LINKTM, Mavica, PictureGear, Memory Stick and the Memory Stick logo, VAIO and the VAIO logo are trademarks of Sony Corporation. Windows and the Windows 98 logo are registered trademarks of Microsoft Corporation. All other trademarks are trademarks of their respective owners. t t t t t Specifications are subject to change without notice. Opening the unit, for whatever reason, could lead to damages that are not covered by the guarantee. [. . . ] To return to normal mode Press any key. System Hibernation Mode The state of the system is saved on the hard drive and power is turned off. The power indicator light is off in this mode. To activate System Hibernation mode Press Fn+F12. You can also use the PowerPanel utility to enter System Hibernation mode. To return to normal mode Turn on the computer by sliding the power switch forward. The computer returns to its previous state. u Steps to return to normal mode: System hibernation b System suspend b System Idle System suspend requires less time than System hibernation. Power consumption: System idle b System suspend b System hibernation System idle uses more power than System hibernation. u When returning from System hibernation mode, the system status stored on the hard disk is erased and the computer starts normally if you slide the power switch forward and hold for more than four seconds. 46 Using Your Notebook Computer Using a Second Battery Pack You can purchase a second rechargeable battery pack. With two battery packs, you can extend the time that you use your computer with battery power. When using two battery packs, the battery pack you insert first charges first. The battery pack you insert second charges when the first battery pack is 85 percent full. You can monitor which battery pack is charging by observing the battery indicator lights. To insert a second battery pack 1 2 If another device is in the multi-purpose bay, remove the device. The battery 2 indicator light turns on. Multi-purpose bay Battery pack Label side facing down 3 Attach the Weight Saver to the computer to stabilize the battery pack. Slide the eject lever on the bottom of the Weight Saver toward the front of the computer to lock it. After setting your network configuration, you will be able to use the LAN functionality. 55 Sony Notebook Computer User Guide Port Replicator Your notebook computer supports the use of an optional port replicator. Attaching a port replicator enables you to connect additional peripherals to your computer. 1 2 3 4 / Network (ethernet) Monitor (page 60) Serial (page 63) Mouse/Keyboard (page 69) 5 6 7 USB (page 72) Printer (page 59) DC In (page 17) The port replicator can be powered only with an AC adapter supplied with your notebook or the optional PCGA-AC71 AC adapter. Do not remove the AC adapter from the port replicator or the AC outlet while using the port replicator; this may cause data damage or hardware malfunctions. All connectors are SELV (Safety Extra Low Voltage) according to EN60950. 56 Connecting peripheral devices To attach your computer to the port replicator Use the AC adapter supplied with your computer or the optional Sony PCGA-AC71 adapter. To disconnect your port replicator completely from mains voltage unplug the AC adapter. When attaching your computer to the port replicator, do not attempt to insert or remove the battery pack. Lifting and turning the computer with attached port replicator may cause a temporary loss of power. Please make sure that the socket outlet is easily accessible. To supply power to your computer while it is connected to the port replicator, you must connect the AC adapter directly to the port replicator. 1 2 Turn off your computer and disconnect all peripherals. On the bottom of the computer, lift the port replicator port cover. port replicator port 3 Attach the bottom of the computer to the port replicator connector until it clicks. Notebook computer Port replicator 57 Sony Notebook Computer User Guide 4 Plug the cable attached to the AC adapter into the DC IN connector on the port replicator. Plug the power cord into the AC adapter and an AC outlet. AC adapter Power cord (hazardous voltage according to EN60950) SELV according to EN60950 5 The power indicator light turns green. Levers Power Port replicator connector 6 Turn on the computer. When you use the port replicator for the first time, the installation of the network driver starts automatically. When the installation is complete, a message: "Do you want to restart your computer?" will appear. The floppy disc supplied with your Port Replicator is useless. 58 Connecting peripheral devices Printer You can connect a Windows-compatible printer to your computer to print documents. To connect a printer u Use the symbol to locate the Printer connector. [. . . ] Do not drop the computer or place heavy objects on top of the computer. On Installation u Do not place your computer in a location subject to: u u u u u u u u Heat sources, such as radiators or air ducts Direct sunlight Excessive dust Moisture or rain Mechanical vibration or shock Strong magnets or speakers that are not magnetically shielded Ambient temperature of more than 35º C or less than 10º C High humidity 86 u u u u u u u Do not place electronic equipment near your computer. Do not place your computer on porous surfaces such as rugs or blankets, or near materials such as curtains or draperies that may block its ventilation slots. Leave a space of at least 8 inches behind the back panel of the computer. The computer uses high-frequency radio signals and may cause interference to radio or TV reception. [. . . ]