[. . . ] LCD Projector User Manual
X300
MODEL
LVP-X300U
EN 1
APPENDIX
ESPAÑOL
ITALANO
DEUTSCH
FRANÇAIS
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. If you use another power-supply cord, it may cause interference with radio and television reception. Use the attached RGB cable, RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class A device. [. . . ] · When the temperature around the projector becomes too high, the sign "TEMP!!" blinks red on the screen. If the temperature stays too high, the lamp will be shut off automatically . The projector automatically shuts off when the lamp is used up in about 2, 000. You must replace the lamp.
30
· The volume control bar will disappear about 10 seconds after releasing the volume buttons. · The volume buttons do not work when MENU selection bar or MENU is displayed. · The volume from the audio output terminals and PC audio output terminal are not changed. · If the high level of audio signal, for example DVD is supplied into PC AUDIO IN terminal, the speaker out may be distorted.
EN 14
Menu operation
PICTURE CONTRAST R ± 30 CONTRAST B ± 30 BRIGHTNESS R ± 30 ± 30 BRIGHTNESS B (± 2 : When the source is selected to COMPUTER) (Displays only when the source is selected to VIDEO) (Displays only when the source is selected to VIDEO)
SHARPNESS TINT COLOR AUDIO BASS TREBLE PinP AUDIO IMAGE REVERSE KEYSTONE AUTO POWER ON AUTO POWER OFF TEST SIGNAL MENU POSITION MODE DISPLAY SPLASH SCREEN CINEMA MODE VIDEO SIGNAL LANGUAGE HORIZ. POSITION VERT. POSITION FINE SYNC. TRACKING COMPUTER INPUT USER
0-3 0-3 (Main) ,
(Sub) R R
INSTALLATION
(Invert) , (Mirror invert) R (Off) , R (Mirror) , ± 15° ON , OFF 0 (Off) , 5 , 10 , 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 55 , 60 min. ON , OFF (Upper left), (Lower right) ON , OFF ON , OFF ( : When the source is selected to COMPUTER) AUTO , OFF AUTO , NTSC , PAL , SECAM , 4. 43NTSC , PAL-M , PAL-N , PAL-60 , English , Español , Deutsch , Français , Italiano , 0 - 999 * 0 - 999 * 0 - 32 0 - 9999 * RGB , YCBCR , YPBPR HOLD BEGIN HOLD END CLAMP POSITION CLAMP WIDTH ANAMORPHIC 1 - 99 1 - 99 0 - 63 0 - 63 ON , OFF
OPTION
SIGNAL
* : Setting range is different according to the type of the signal.
* * * *
Basic operation
Several settings can be adjusted using Menu. Press the { or } button to select AUTO POWER OFF.
AUTO POWER ON AUTO POWER OFF
TEST
ON 0 min
TEST SIGNAL
ON OFF
1. Press the $ or % button to adjust auto power off time.
AUTO POWER ON AUTO POWER OFF
TEST
PICTURE
ON 30 min ON OFF
2. Press the $ or % button to select the OPTION menu.
Opt
TEST SIGNAL
INSTALLATION
3. · If the menu operation is not working, press the RESET button on the terminal board using the suitable implement · If the COMPUTER or VIDEO button is pressed, the MENU selection bar or MENU will disappear. · The settings with 2 mark, you should press the ENTER button after selecting.
INSTALLATION
TEST
IMAGE REVERSE KEYSTONE AUTO POWER ON AUTO POWER OFF
R
0° ON 0 min
TEST
TEST SIGNAL
ON OFF
EN 15
ENGLISH
CONTRAST BRIGHTNESS COLOR TEMP.
± 30 ± 30 1 (Standard) 2 (High) 3 (Low) 4 (User) ± 10 ± 10 ± 10
Menu operation (continued)
1 PICTURE CONTRAST . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO). Adjusts the color intensity of the image (displays only when the source is selected to VIDEO).
Opt
2 AUDIO BASS . . . . . . . . . . . . . . . . . . . Use to select the audio output in the PinP mode, or (Sub).
Opt
(Main)
AUDIO
BASS TREBLE PinP AUDIO 1 1
/
3 INSTALLATION IMAGE REVERSE Use to reverse or invert the projected image. (Mirror invert) is effective INSTALLATION when the projector is ceiling-mounted. If the image has KEYSTONE 0° keystone distortion, select the approximate setting. You can use it only when IMAGE AUTO POWER OFF 0 min REVERSE is (Invert) or (Mirror invert). To select whether to boot up automatically when the power is turned on external to the projector. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. [. . . ] When having a control sequence by RS232C, reject other codes from personal computer side. · * : The sending time of return command may delay depending on the condition (during changing the input signal, etc. ).
[Example] Turn the power ON (' 'is for ASCII code)
Sending commands from the PC etc. 30 30 21 0D '0' '0' '!' ' ' Status code from projector Meaning Command for POWER ON 30 30 21 0D '0' '0' '!' ' ' Command received (Command echo back)
4) Operation commands
The operation commands execute the basic operation setting of this projector. It may not operate when changing the signal.
Operation POWER ON POWER OFF INPUT COMPUTER 1 INPUT COMPUTER 2 INPUT VIDEO 1 INPUT VIDEO 2 ASCII ! [. . . ]