[. . . ] IFU-TL HR GB. fm Page 1 Friday, November 7, 2008 2:30 PM
CONTENTS
DEFINITION OF USE BEFORE USING THE WASHING MACHINE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE BEFORE THE FIRST WASH CYCLE PREPARATION OF THE WASHING DETERGENTS AND ADDITIVES CLEANING THE FILTER/ DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING INSTALLATION ELECTRICAL CONNECTION
Black process 45. 0° 100. 0 LPI
IFU-TL HR GB. fm Page 2 Friday, November 7, 2008 2:30 PM
DEFINITION OF USE
This washing machine is exclusively destined to wash machine washable laundry in quantities which are usual for private households. • Observe the instructions given in these Instructions for Use and the Programme Chart when using the washing machine. • Keep these Instructions for Use and the Programme Chart; if you pass on the washing machine to another person, also give him/her Instructions for Use and Programme Chart.
BEFORE USING THE WASHING MACHINE
1. Remove the bottom protection by tilting and turning the washing machine on one rear bottom corner. [. . . ] Reconnect the washing machine.
2
6
GB 9
Black process 45. 0° 100. 0 LPI
IFU-TL HR GB. fm Page 10 Friday, November 7, 2008 2:30 PM
CARE AND MAINTENANCE
Detergent dispenser
Clean the detergent dispenser regularly, at least three or four times a year, to prevent detergent build-up: 1. Replace the dispenser by locating the bottom tabs in the lid holes and pivot until both of the upper buttons lock. Note: ensure that the detergent dispenser is correctly reinstalled.
Water inlet hose filter
Check and clean regularly (at least two or three times a year). Carefully clean the filter located at the end of hose, without disassembling it, for example with a tooth-brush. Plug the washing machine back in.
Safety valve inspection window
A
B
Water inlet hose
Check the inlet hose regularly for brittleness and cracks and replace it if necessary using a new hose of the same type. The inlet hose as shown on picture “A” has a safety valve to prevent the appliance against uncontrolled water inlet; if the safety valve inspection window is red, the safety valve has been activated and the hose must be exchanged. Contact out AfterSales Service or your specialist dealer to obtain a new inlet hose. “B”), periodically check the colour of the transparent coating. If the transparent hose coating turns into an intense red, this is an indication that the hose may have a leak and should be replaced. Contact our After-Sales Service team or specialist dealer to obtain a replacement hose.
C
GB 10
Black process 45. 0° 100. 0 LPI
IFU-TL HR GB. fm Page 11 Friday, November 7, 2008 2:30 PM
Appliance exterior and control panel
• Clean with a soft damp cloth. • If necessary, a neutral household cleaner can be applied (do not use aggressive or abrasive products).
Lid seal
• Check the condition of the lid seal periodically and clean it from time to time with a damp cloth.
Water inlet hose(s)
• Check the hose regularly for brittleness and cracks. Replace if necessary.
Appliance interior
• After each washing, leave the lid open for some time to allow the inside of the appliance to dry. • If you never or seldom wash your laundry at 95°C, we recommend to occasionally run a 95°C programme without laundry, adding a small amount of detergent, to keep the interior of the appliance clean.
Filter
• Check and clean the filter regularly, at least 3 or 4 times a year (see “Cleaning the Filter/ Draining Residual Water”).
Do not use flammable fluids for cleaning the appliance. Recovering an object that falls between the drum and the tub
If an object accidentally falls between the drum and the tub, you can recover it thanks to one of the removable drum blades: 1. Using a screw-driver, press on the plastic end while sliding the blade from left to right. Open the drum: you can recover the object through the hole in the drum. Refit the blade from inside the drum: Position the plastic tip above the hole on the right side of the drum. Close the drum flaps again, turn the drum through half a turn and check the positioning of the blade at all its anchorage points. Plug the washing machine in again.
3
4
4
7
GB 11
Black process 45. 0° 100. 0 LPI
IFU-TL HR GB. fm Page 12 Friday, November 7, 2008 2:30 PM
TROUBLESHOOTING GUIDE
Your washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and allow you to react appropriately. These faults are frequently so minor that they can be removed within a few minutes. Problem Causes, Solutions, Tips
Appliance does not start, • Plug is not properly inserted in socket. no indicator lamps are on • Socket or fuse does not function correctly (use a table lamp or similar appliance to test it). [. . . ] • The inlet hose and the plastic enclosure contain (depending on model) electrical components: do not cut the hose and do not immerse the enclosure in water. • If the flexible hose is damaged, unplug the washing machine from the mains immediately, turn off the tap and replace the hose. If the flexible hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales Service or from your dealer). This operation must be carried out exclusively by a qualified technician.
Connect the water drain hose
1. [. . . ]