[. . . ] ATMOSPHERIC Hot Water Dispenser AWD-12 Series Installation & Operating Manual I&W #07. 05. 126. 00 This manual contains important safety information concerning the maintenance, use and operation of this product. Failure to follow the instructions contained in this manual may result in serious injury. If you are unable to understand the contents of this manual, please bring it to the attention of your supervisor. Do not operate this equipment unless you have read and understood the contents of this manual. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. [. . . ] See Figure 5. · The three buttons underneath the LED display dispense at pre-programmed quantities of 2QT, 3QT & 4QT as marked. 2QT = 2 quarts (1. 9 liters) 3QT = 3 quarts (2. 8 liters) 4QT = 4 quarts (3. 8 liters) NOTE: The dispense amounts can be adjusted if required. · The red button can be pressed any time after pressing one of the programmed dispense buttons to stop dispensing. In addition, the red button can be pressed and held in to manually dispense water. Water will continue to flow until the red button is released. 5 Form No. AWDM-0704 OPERATION ERROR CODES There are four error codes that may show in the display: E1: Indicates that the display temperature is out of range or display temperature probe is malfunctioning. E2: Indicates that the control temperature is out of range or control temperature probe is malfunctioning. H2O: Indicates that the inlet water solenoid has been running continuously for an excessive period of time. Check for problems with the water supply or internal water leak. Adjustable from 75° - 195°F (82° - 91°C) in 1 degree intervals. Setting Temperature Setpoint '# PROGRAMMING THE DISPENSER WARNING To avoid any injury, turn the power switch off at the fuse disconnect switch/circuit breaker or unplug the unit from the power source and allow to cool completely before performing any maintenance or cleaning. Dipswitch Panel A dipswitch panel is located on the back of the control board which is behind the front panel graphic overlay. The switches have the following functions: Switch 1 is used to switch between operational (Run) mode and Programming mode. Switch 2 is used to change the temperature display from F° to C°. Switch 3 is used to select the type of operation, and must be switched to the right-hand position for the dispenser to operate. Turn the power switch to the OFF position and unplug the unit from the electrical outlet. Move dipswitch 2 to the left, (when facing the controls) to change the display from Fahrenheit (F°) to Celsius (C°). Plug the unit into the proper electrical outlet and turn the power switch to ON. Form No. Turn the power switch to the OFF position and unplug the unit from the electrical outlet. Move dipswitch 1 to the left, (when facing the controls) to enter programming mode. Plug the unit into the proper electrical outlet and turn the power switch to ON. Press the RED manual dispense button and the display will now read the current temperature setpoint. Use the 2QT and 3QT buttons to adjust the temperature setpoint up or down. [. . . ] LIMITATION OF REMEDIES AND DAMAGES Hatco's liability and Buyer's exclusive remedy hereunder will be limited solely, at Hatco's option, to repair or replacement by a Hatcoauthorized service agency (other than where Buyer is located outside of the United States, Canada, United Kingdom or Australia in which case Hatco's liability and Buyer's exclusive remedy hereunder will be limited solely to replacement of part under warranty) with respect to any claim made within the applicable warranty period referred to above. Hatco reserves the right to accept or reject any such claim in whole or in part. Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer's sole expense. HATCO WILL NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS RESULTING FROM THE USE OF OR INABILITY TO USE THE PRODUCTS OR FROM THE PRODUCTS BEING INCORPORATED IN OR BECOMING A COMPONENT OF ANY OTHER PRODUCT OR GOODS. Form No. [. . . ]