[. . . ] : : : :
Important Safety Instruction
BASIC SAFETY PRECAUTIONS This guide contains many important safety messages. Always read and obey all safety messages.
w This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others or cause damage to the product. All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER, WARNING, or CAUTION. [. . . ] In order to prevent possible electric shock, this appliance must be grounded. Improper use of the grounding plug can result in an electric shock.
Don't store Grounding (Earthing)
15
Introduction
Important Safety Instruction
w Warning
w Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction. w Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. w Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. w The refrigerant and insulation blowing gas used in the appliance require special disposal procedures. When disposal, please consult with service agent or a similarly qualified person.
This appliance contains a small amount of isobutane refrigerant (R600a), natural gas with high environmental compatibility, but it is also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes. In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. The room must be 1m2 in size for every 8g of R600a refrigerant inside the appliance. · If the failure occurs at product and it does not operate by pressing any button and normal indication is not done, do not turn the power off and immediately contact with the local service center. · A lot of time is needed for service engineer to detect the failed part by turning it off. For LED Model · Pressing this button stops operation of other buttons. · "Locking" or "Un-Locking" is repeated whenever pressing the LOCK button. (For "Locking" press the "LOCK" button for 3 secs. For "Un-Locking" press the "LOCK" button for 1 secs. ) · When `LOCK' is activated, pressing the other buttons would not work.
Lock
In selecting "LOCK"
In selecting "UNLOCK"
On/Off
· Pressing this button refrigerator power is ON or OFF. For "ON" press the "ON/OFF" button for 1 secs. ) · LED lamp is operated automatically for all day. It may makes vegetable to photosynthesize.
Vita Light (Optional)
Vita Light (LEDs are located at the rear of the vegetable drawer)
· Viewing the laser out put with certain optical instruments (e. g. Contact qualified service technician if there is any failure in LEDs.
w Caution
25
· Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Operation
Door Alarm
· When the door of the fridge is left opened for a while, the alarm sounds. Please contact with the local service center if warning continue to sound even after closing the door. · Take out the water container, fill it up and put it back to it's original location.
Ice Making
· If you close Freezer Door or push Water tank button, Water falls to the ice making compartment. [. . . ] · The Anti-Condensation pipe is installed around the front side of fridge-freezer as well as on the partition between fridge compartment and freezer compartment to prevent dewing.
Anti-Condensation Pipe
If You Move
Anti Condensation Pipe
· Especially after installation or when ambient temperature is high, the fridge-freezer may feel hot, which is quite normal.
33
Care and Maintenance
Lamp Replacement
1. Remove the room lamp lid by taking down while pulling its back projection. Replacement bulb must be the same specification as original.
w Caution
· You must check the O-RING, which is made by rubber and prevent electric spark. · Don't touch the lamp, in case of light on the long time. [. . . ]